manualshive.com logo in svg

Crestron TSW-570P, Product Manual

Share
Download
Crestron TSW-570P Product Manual Download Page 181

Product Manual — Doc. 8550E

TSW-70 Series • 175

Web Configuration

The touch screen may be monitored and configured using the included web configuration
interface. The configuration interface is accessible from a web browser if the touch screen IP
address is known.

The web configuration interface is also accessible through the XiO Cloud® service. For more
information, refer to

Connect to XiO Cloud Service (on page 215)

.

To access the configuration interface:

1. Use the Device Discovery tool in Crestron Toolbox™ software to discover the touch screen

and its IP address on the network.

2. Open a web browser.

3. Enter the touch screen IP address into the browser URL field. The configuration interface

is displayed (TSW-1070 shown).

NOTE:

If authentication is enabled for the touch screen, an administrator username and

password must be entered prior to accessing the web configuration interface. For more
information on configuring authentication settings, refer to

Authentication (on

page 201)

.

Web Configuration Interface

The configuration interface provides the following tabs:

l

Status: Used to monitor touch screen status

l

Settings: Used to configure touch screen settings

l

Security: Used to enable authentication and other security settings

Summary of Contents for TSW-570P



































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands