background image

Crestron 

ST-TUNE

 Integrated AM/FM/TV Tuner

 

Operations Guide - DOC. 5833A Integrated AM/FM/TV Tuner: ST-TUNE  

••

  15 

The next four sections describe a ST-TUNE within a SIMPL Windows program. The 
first section provides initial configuration information, the second section details the 
SIMPL symbol, the third section describes how a basic example program works by 
using a textual description and a block diagram, and the fourth section describes the 
screens of an advanced example program.  

NOTE:

  The following descriptions assume that the reader has knowledge of SIMPL 

Windows. If not, refer to the extensive help information provided with the software.  

NOTE:

  VT Pro-e (version 2.1.8 or later) is required for the ST-TUNE example 

touchpanels. The latest software version can be obtained from the What’s New page 
(VisionTools Pro-e section) or Downloads page (VTPRO-E Library) of Crestron’s 
website (www.crestron.com). New users are required to register in order to obtain 
access to the FTP site. 

NOTE:

  There is no need to recreate the ST-TUNE example touchpanels or example 

SIMPL Windows programs. Both are available from the Downloads page 
(EXAMPLES Library) of Crestron’s website (www.crestron.com). Search for 
STTUNEA.ZIP that contains a basic example and STTUNEB.ZIP that contains an 
advanced example. Each example contains the program and all associated files 
required to complete the program.  

Configure ST-TUNE Program 

To create a program with a ST-TUNE, in the Configuration Manager of SIMPL 
Windows, refer to the table below for initial configuration information.  

Configure ST-TUNE Program 

DEVICE

SYMBOL

DROP

ADDITIONAL

LIBRARY

REQUIRED

WHERE

SETUP

Control 
Systems

Desired control 
system

System Views

Refer to the documentation 
supplied with the control system 
for additional setup information.

ST-TUNE or 
STI-TUNE

Network 
Control 
Modules

System Views, 
Cresnet Units

CHANGE NET ID (OPTIONAL) - 
Double-click on ST/I-TUNE (or 
single-click then right mouse-
click) on ST/I-TUNE. Select 
Configure. Select NET ID then 
select desired hexidecimal ID.

 

ST-TUNE and STI-TUNE Symbols 

The diagrams on the next two pages show the ST-TUNE and STI-TUNE symbols in 
SIMPL Windows. The two tables following the diagrams list the inputs and outputs, 
respectively, and their functional descriptions. 

NOTE:  

The US version ST-TUNE and international version STI-TUNE have the 

same default NET ID. If both ST-TINE and STI-TUNE are used in the same Cresnet 
system, refer to “Identity Code” that begins on page 10 for further information. 

NOTE:

  All signals listed in the following tables apply to the US version ST-TUNE 

and international version STI-TUNE except where noted. 

Summary of Contents for ST-TUNE









































Reviews: