Crestron ST-LT Operation Manual Download Page 5

 CRESTRON  

Lutron Interface 

Description 

Functional Description 

There are two CRESTRON Lutron Interface configurations available: ST-LT and 
STI-LT. Configuration differences depend on which power pack is supplied. The 
ST-LT includes a power pack for a 120V AC supply and the STI-LT includes a 
power pack for 220V AC. For purposes of this Operations Guide, the term ST-LT is 
used for either configuration.  

The ST-LT is a device that permits the CRESTRON CRESNET II System or 
SmarTouch STS to interface with a Lutron GRAFIK Eye Lighting System. Future 
ST-LT production models shall permit an interface with the Lutron Homeworks 
System. If the ST-LT is part of the CRESNET II System, use of the supplied power 
pack is optional.  

Physical Description 

The ST-LT is housed in a black enclosure with silk-screened labels on the front and 
rear panels. On the front of the unit there are seven LEDs for indicating the unit’s 
current status. All connections are made on the back of the unit. Refer to the physical 
views shown after this paragraph. There are four rubber feet on the base of the unit 
for stability and to prevent slippage.   

Operations Guide - Doc. 5694 

Lutron Interface  

  1 

Summary of Contents for ST-LT

































Reviews: