2-Way RF Wireless Touchpanel
Crestron
STX-1700CXP
10
•
2-Way RF Wireless Touchpanel: STX-1700CXP
Operations Guide - DOC. 6144
ADDITIONAL RF SETUP
Press the
ADDITIONAL SETUP
button to display the ADDITIONAL RF SETUP
screen. In situations where two or more touchpanels are in close proximity and could
conflict with each other, press the
SET LOW POWER
button to reduce the
touchpanel’s power and minimize the possibility of interference. The factory default
setting is
SET HIGH POWER.
Use the
PREVIOUS
and
NEXT
buttons to choose the desired frequency band. The
choices correspond with the names shown in the following table. The table shows
the 802.11b channels within each band that are occupied by the STX-1700CXP.
Selection of a band is based on a number of factors, including the need to avoid
interference with nearby RF devices, and compliance with local communication
laws. In the US, Crestron recommends using Bands 5 (USA comp 1) through 9
(USA comp 5). Bands 1 through 4 (France, Spain, Japan, and Canada) are intended
for use in Cresnet systems outside the US. The default setting is Band 0, USA
(original), which is
not
Wi-Fi friendly. At this setting, the touchpanel can
communicate with a TPS-RFGWX gateway whether it is Wi-Fi friendly or not, since
Band 0 is the default for both versions of the gateway. Note that the touchpanel and
gateway must be set to the same band in order to communicate.
1
2
3
4
5
6
7
8
9 10 11 12 13 14
0
2400-2474
USA (original)
•
•
•
•
•
•
•
•
•
•
•
•
•
1
2448-2474
France
•
•
•
•
•
•
•
2
2448-2474
Spain
•
•
•
•
•
•
•
3
2471-2497
Japan
•
•
•
•
4
2452-2477
Canada
•
•
•
•
•
•
•
5
2400-2425
USA (comp 1)
•
•
•
•
•
6
2409-2435
USA (comp 2)
•
•
•
•
•
•
•
7
2419-2445
USA (comp 3)
•
•
•
•
•
•
•
•
8
2430-2455
USA (comp 4)
•
•
•
•
•
•
•
•
•
9
2440-2465
USA (comp 5)
•
•
•
•
•
•
•
•
•
Occupied 802.11b Channels
Band
#
Freq.
Range
(MHz)
Band Name
In the table, a bullet (•) indicates channels that are used by the STX-1700CXP. The unmarked channels
can be used by other devices communicating near the Cresnet system, thus minimizing interference.
After the Cresnet ID, RF ID, RF CHANNEL, and Band settings have been verified,
touch the
Return
button at the bottom of the screen to save settings and display the
SELECT INTERFACE screen. Touch
Return
again to display the SETUP MENU.
KEY CLICK SETUP
Key Click Setup
From the SETUP MENU, press the
Key Click Enabled
button to open KEY CLICK
SETUP screen. (If the function is currently disabled, the button legend is “
Key Click
Disabled
.”) To enable an audible tone (beep) when the touchpanel buttons are
pressed, select among the
Short, Med,
or
Long
KEY CLICK ENABLE/LEN buttons
to set the duration of the tone. The touchpanel responds with a corresponding signal.
To disable the feature, select
Click Off
.
Use the KEY CLICK VOLUME
UP
and
DOWN
buttons to increase and decrease the
volume of the signal. The area to the right of the buttons shows the relative volume
from 0% to 100%, both as a numeric value and, for a quick visual reference, as an
analog bar.
Select the
Return
button to return to the SETUP MENU.