Crestron GLX-DIM6 Installation Manual Download Page 1 | Manualshive

Page: 1 / 16

Crestron GLX-DIM6 Installation Manual Download Page 1

CRESTRON GREEN LIGHT™ Architectural Dimming

Introduction

CRESTRON GREEN LIGHT architectural dimming cabinets come pre-configured with GLX architectural dimming
and switching modules already installed. In addition, branch circuit breakers come preinstalled and prewired to the
modules. The cabinets only require installation and wiring of feed and load circuits.

Industry Compliance

The cabinet and modules are Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.

(E227280 (cabinet) and E103692 (modules))

Application

The following diagram shows CRESTRON GREEN LIGHT architectural dimming cabinets in a lighting application
that is controlled by an IPAC system.

CRESTRON GREEN LIGHT Architectural Dimming Cabinets in a Typical Lighting Application

Crestron Electronics, Inc.

Installation Guide – DOC. 6688A

15 Volvo Drive Rockleigh, NJ 07647

(2020963)

Tel: 888.CRESTRON

02.09

Fax: 201.767.7576

Specifications subject to

www.crestron.com

change without notice.

1
2
3
...
»

Summary of Contents for GLX-DIM6

















Reviews:

No comments