8.
Slide the module down into the appropriate module
slot. Use the guide ribs on the front and rear of the
module to help position it in the assembly.
Position the FT2A-CHGR-USBA-BASIC Module
FlipTop
assembly
Retracted
lid
Front
guide rib
Module
Engraved
icon
9.
Confirm that all modules are level with their
surroundings and place the locking bars (removed in
step 3) into position so that the screws on either side
engage the screw holes in the assembly.
10.
Using a manual torque screwdriver set to its lowest
possible setting, hand tighten the locking bar screws
until the locking bars are secured to the FT2 FlipTop
assembly.
Position the Locking Bars and Bezel
FlipTop
assembly
Retracted
lid
Locking
bars (2)
Lid
retraction
button
Bezel
Bezel
opening for
retracted lid
11.
Place the bezel (removed in step 2) onto the FT2
FlipTop assembly so that the retractable lid fits inside
the bezel opening. The bezel is held in place using
magnets.
12.
Plug the assembled power pack into an AC outlet.
Operate the Module
To operate the USB rapid charging module:
1.
Tap the lid retraction button to retract the one-touch
lid, which disappears into the FT2 FlipTop assembly.
2.
Connect the USB Type-A connector from the mobile
device needing a charge to one of the two USB Type-A
charging ports on the module.
3.
Confirm that the charging indicator on the mobile
device shows that the device is charging.
For Additional Information
Scan or click the QR code for detailed product information.
Compliance and Legal
Original Instructions:
The U.S. English version of this document is the original
instructions. All other languages are a translation of the original instructions.
As of the date of manufacture, the product has been tested and found to
comply with specifications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
following conditions: (1) This device may not cause harmful interference and (2)
this device must accept any interference received, including interference that
may cause undesired operation.
CAUTION:
Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user’s authority to
operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
The product warranty can be found at
www.crestron.com/warranty
.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents
.
Certain Crestron products contain open source software. For specific
information, please visit
www.crestron.com/opensource
.
Crestron, the Crestron logo, and FlipTop are either trademarks or registered
trademarks of Crestron Electronics, Inc. in the United States and/or other
countries. Other trademarks, registered trademarks, and trade names may
be used in this document to refer to either the entities claiming the marks and
names or their products. Crestron disclaims any proprietary interest in the
marks and names of others. Crestron is not responsible for errors in typography
or photography.
©2019 Crestron Electronics, Inc.
Crestron Electronics, Inc.
15 Volvo Drive, Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Quick Start - Doc. 8423B
(2053080)
03.19
Specifications subject to
change without notice.
