DO
GUIDE
Installation of the power pack in the holder appears as shown
below.
DO
Complete the Connections
Make additional connections as appropriate for the application.
Front Panel Connections
Rear Panel Connections
DO
Set the IP Address
The configuration of the receiver within the DigitalMedia 8G+
®
system determines how the IP address of the receiver is set:
• If the receiver connects to a DigitalMedia™ switcher, the
receiver is configured by the switcher automatically.
• If the receiver connects to a DigitalMedia 8G+ transmitter,
the receiver uses its own configuration settings. By default,
DHCP (Dynamic Host Configuration Protocol) is enabled.
The default IP address can be assigned to the receiver by
holding down the
SETUP
button while the unit boots up.
The default IP address overwrites the current setting.
The default IP address of the DM-RMC-200-C is
192.168.1.245. To manually set a different IP address, use
the Crestron Toolbox™ application.
DOC. 7549C (2042263) 09.16
Specifications subject to change without notice.
DO
Learn More
Visit the website for additional information and the latest
firmware updates. To learn more about this product, use a QR
reader application on your mobile device to scan the
QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested and found to comply with specifications for CE marking.
This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.
Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION:
Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The specific patents that cover Crestron products are listed at
http://www.crestron.com/legal/patents
.
The product warranty can be found at
www.crestron.com/warranty
.
Certain Crestron products contain open source software. For specific information, please visit
www.crestron.com/opensource
.
Crestron, the Crestron logo, Crestron Toolbox, DigitalMedia, DigitalMedia 8G+, and DM are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/
or other countries. HDBaseT and the HDBaseT Alliance logo are either trademarks or registered trademarks of the HDBaseT Alliance in the United States and/or other countries. HDMI and the
HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. UL and the UL logo are either trademarks or registered trademarks
of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the
entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or
photography.
This document was written by the Technical Publications department at Crestron.
©2016 Crestron Electronics, Inc.
24 V
2.5A MAX:
From power
pack (included)
AUDIO OUT R, L
(SPEAKER):
Amplified stereo
audio output
AUDIO OUT R, L
(LINE):
Stereo unbalanced
line level
audio output
LAN:
10BASE-T/
100BASE-TX
Ethernet to local
network device
DIG IN:
Software
programmable
digital input
USB HID:
From USB
HID-compliant
device
HDMI OUT:
HDMI
®
digital
video/audio
output
IR:
To IR
controllable
device
COM:
To RS-232
device
