manualshive.com logo in svg

Crest Audio X 18R, Owner'S Manual, Page: 43 / 56

Share
Download
Crest Audio X 18R Owner'S Manual Download Page 43

Front Panel Features

MONITOR Output Section

SOURCE SELECT

The Source select portion of the Monitor system allows you to assign the primary mix 
buses to the Monitor outputs.

NOTE:

  All buses are monitored pre-fader (post-insert)

NOTE:

  All selected sources are added (summed) together.

TAPE IN

Assigns the TAPE IN L & R signals to the monitors. The TAPE IN jacks are located 
on the rear panel. 1/4” TRS  jacks and RCA phone plugs are provided for easy 
hookup.

A1-2  (Aux 1 & 2)

Assigns Auxes 1 and 2 to the Monitor outputs.  Auxes 1 and 2 are configured 
as a paired-stereo Aux bus (see Mono input channel description).  Aux 1 is Left 
and 2 is Right.

MONO

 Assigns the Mono bus to both the Left and Right Monitor outs.

L-R (Left & Right)

 Assigns the Left and Right buses to the Left and Right Monitor outs.

G1-2 (Groups 1 & 2)

 Assigns Groups 1 and 2 to the Monitor outs. Group 1 is Left and 2 is Right.

G3-4 (Groups 2 & 4)

 Assigns Groups 3 and 4 to the Monitor outs. Group 3 is Left and 4 is Right.

Master Section

3

p. 43

Summary of Contents for X 18R

























































Reviews:

No comments