manualshive.com logo in svg

Creek Audio CD50 mk2, Instruction Manual, Page: 11 / 12

Share
Download
Creek Audio CD50 mk2 Instruction Manual Download Page 11

11

CD50 mk2 Compact Disc Player

TROUBLESHOOTING GUIDE

If you have followed the instructions, and are having difficulty operating your compact disc player, please use the simple
guide below to help you solve the problem.  Here we have listed the most common hiccups experienced by the users,
which we hope will be of some help.

Locate the SYMPTOM in table below and then check the corresponding POSSIBLE CAUSE and CORRECTIVE ACTION
to remedy the problem.

SYMPTOM    

POSSIBLE CAUSE                    

CORRECTIVE ACTION

No power when the      

Poor power plug connection at   

Insert the power plug firmly into            

power switch is ON.

the AC outlet

the AC outlet

Fuse in the mains plug has blown

Replace the fuse in the mains plug

CD Player is in Stanby mode

Press Standby button

Display does not read T.O.C.

The disc is loaded upside down

Reload the disc with the label side up

The disc is too dirty or scratched

Clean the disc

A DVD or SACD is being used

Replace the DVD with a CD disc

No sound

Improper output cable connections

Connect the output cable properly

Improper amplifier operation

Make sure that the amplifier controls 
are set properly

Sound skips

Damaged, faulty or dirty disc

Clean or replace with a new disc

The CD player is subject to vibrations 

Change the location of the player

or physical shock

Programmed sequence

The CD player is in the normal

Press the STOP button and then 

will not play

disc play mode

program the tracks

Humming noise

Loose cable connections

Press plugs in firmly

Local interference

Move player to new location

Remote handset will 

Batteries low

Replace the batteries

not function.

SPECIFICATION

Power requirements

Supplied 220/240—50 Hz or 100/120—60Hz

Power consumption

20 W max   6 W standby

Frequency response

1 Hz - 20 kHz ±  0.25 dB

Output level

2.0 V RMS at 1kHz, 0 dB

Output impedance

50

Ω

,  min load 1 K 

Ω

Laser type

Semiconductor ALGaAs

Wavelength

790 nm ± 25 nm

Light output (cw)

0.18 mW typical

THD + Noise

> -97dB

Dynamic range

> 117dB

Number of channels

2                                                               

Total harmonic distortion  

<  0.0008% at 1 kHz, 0 dB                 

Weight

5 Kg  / 11 lbs  

Dimensions 

430 x 62 x 250 mm

Summary of Contents for CD50 mk2













Reviews:

No comments