LPN000241 REV B
TO INSTALL:
RECESSED HOUSING COMPATIBILITY
Designed to install in standard 6in recessed downlight
housings.
Compatible with most dimmers when used with multiple
fixtures. Consult ww w.creebulb.com/dimmers for a
compatibility chart.
Compatibility of housings may be determined by
measurement of the housing as detailed in the drawing
above
(Figure 1).
IMPORTANT SAFEGUARDS
WARNING
circuit breaker before installing or servicing.
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
6
. Each lampholder shall be installed only in its intended manner and
orientation.
7
. Suitable for Wet Locations.
8.
Min. temperature rating of -25°C.
9
. Do
10.
11.
SUITABLE FOR INSTALLATION IN A RECESSED CAN WITH
A MAXIMUM OF EIGHT (8) No. 12 AWG THROUGH-BRANCH
CIRCUIT CONDUCTORS SUITABLE FOR 75°C MIN.
WARNING-THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT
OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION
SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION.
MIN. LAMP COMPARTMENT DIMENSIONS
5.5 inch/139.7mm (DIA) x 5.5 inch/139.7mm (H).
not make or alter any open holes in an enclosure of wiring or
electrical components during kit installation.
SAVE THESE INSTRUCTIONS FOR
FUTURE REFERENCE
TRDL6 Series
6” Recessed LED Downlight
1 of 2
Minimum distance
between edge of
fixtu re and top of
housing or other
ob struction.
1
2
STEP 1:
Carefully rotate the“Flip Clips”clockwise
until the clips are fully-dep loyed. See
Figure 2.
NOTE:
For 5" recessed cans, it is
recommended not to rotate the flip clips
into the ful ly dep loyed position.
STEP 2:
Make sure the
POWER IS TURNED OFF
at
the source to the recessed can.
STEP 3:
Remove existing trim and bulb, revealing
the existing recessed socket.
STEP 5:
STEP 4:
Screw the fixture Edison base assembly
into the recessed can socket by turni ng
clockwise. See
Figure 3
.
STEP 6:
Install fixture up into the recessed housing
firmly until trim ring is flush with the
ceiling. Rotate fixtu re clockwise slightly to
tigh ten fit with ceiling and set in recessed
p
il
F
“
e
r
u
s
n
e
,
s
tl
u
s
e
r
t
s
e
b
r
o
F
.
g
n
i
s
u
o
h
m
i
r
t
l
a
t
e
m
h
ti
w
d
e
n
g
il
a
t
o
n
e
r
a
”
s
p
il
C
clips inside of recessed housing during
installation. See
Figure 3 and 4.
3
5.5 inch
(139.7mm)
5.5 inch
(139.7mm)
Flip Clip
•
•
•
1. WARNING
requires knowledge of luminaires electrical systems. If not qua
2. WARNING
– To prevent wiring damage or abrasion, do not expose
wiring to edges of sheet metal or other sharp objects.
3.
4.
WARNING
luminaires that have the construction features and dimensions
shown in the photographs and/or drawings
where the input rating of
the retrofit kit does not exceed the input rating of the luminaire.
SUITABLE FOR TYPE IC LUMINAIRES.
5.
It may be necessary to remove a socket mounting plate for adequate
clearance.
A
B
12.
This device is not intended for use with emergency exit fixtures or
emergency exit lights.
Package Contents:
Part
Description
Quantity
A 6” Retrofit downlight
1
B Edison Socket Adapter
C Field applied label
1
1
Install "Field Applied Label" into the
recessed can.
7.48 inch
(190mm)
