background image

Cree Edge

 

LED High-Output High Bay Luminaire

Transportation, Direct, Pendant, Hook and Cord Mounts

1 of 2

LPN00102X0001A2_A

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should 

always be followed including the following:

READ AND FOLLOW ALL SAFETY 

INSTRUCTIONS

1.  DANGER

- Risk of shock- Disconnect power before installation.

DANGER

 – Risque de choc – Couper l’alimentation avant 

l’installation.

2.  This luminaire must be installed in accordance with the NEC or 

your local electrical code. If you are not familiar with these codes 

and requirements, consult a qualified electrician. 

Ce produit doit être installé conformément à NEC ou votre code 

électrique local. Si vous n’êtes pas familier avec ces codes et ces 

exigences, veuillez contacter un électricien qualifié.

3.  Ensure the mounting surface is capable of supporting the weight 

of the luminaire after installation.

4.  Due to the weight of the luminaire, 3 people may be necessary 

during installation.

SAVE THESE INSTRUCTIONS FOR 

FUTURE REFERENCE

TO INSTALL:

MOUNTING - TRANSPORTATION/

DIRECT MOUNT

STEP 1:

Remove the (4) nuts and washers securing the 
retained Mounting Bracket Bolts to the top of 
the mounting bracket. Remove the top piece 
of the mounting bracket assembly from the 
luminaire. See 

Figure 1.

 

STEP 2:

Align the mounting bracket removed in Step 
1 on an appropriate mounting surface. Using 
customer supplied 3/8” minimum mounting 
bolts, secure the bracket to the mounting 
surface. See 

Figure 2.

STEP 3:

Once the mounting bracket is secured to the 
mounting surface, 

re-secure the luminaire using the nuts and 
washers removed in Step 1 to 180 in/lbs.

STEP 4:

Install a suitable Listed cord strain relief 
brushing or bushing in the customer supplied 
junction box, and feed the luminaire’s cord 
through it. 

STEP 5:

Connect the cord to the supply wiring per the 

Electrical Connections 

section.

MOUNTING - PENDANT MOUNT

STEP 1:

Remove the (4) nuts and washers securing the 
retained Mounting Bracket Bolts to the top of 
the mounting bracket. Remove the top piece 
of the mounting bracket assembly from the 
luminaire. See 

Figure 1.

 

STEP 2:

Install the pendant fitter using (4) supplied 
screws to the top of the mounting bracket. See 

Figure 3.

 

STEP 3:

Secure the mounting bracket to the luminaire 
using the nuts and washers removed in Step 1 
to 180 in/lbs.

STEP 4:

The pendant can be adjusted laterally by the 
pendant fitter to the desired position and then 
tightening the (4) Adjustment Screws. See 

Figure 3.

STEP 5:

Size the customer supplied pendant 
accordingly and ensure that the pendant and 
mounting surface is capable of supporting the 
weight of the luminaire.

1

2

Mounting Bracket 

Bolts (4)

Mounting Holes For Customer 

Supplied 3/8” Mounting Bolts

Adjustment 

Screws (4)

Pendant Fitter

3

NOTES:

•  Pendant and hooks are only supplied with luminaire when ordered 

as “Pendant” or “Hook and Cord” mounting.

•  Prior to installation, store luminaire in a dry location protected from 

rain, dust, and outdoor environment.  If equipped with a photocell 
receptacle, do not store or install luminaire outdoors without 
immediately installing a suitable photocell, shorting cap, or other 
compatible device. Do NOT leave receptacle open to environmental 
elements.  Luminaires with a top-mounted photocell receptacle 
should not be installed in an up-light position or at a tilt greater 
than 45 degrees from the down-light position.

Reviews: