2 of 3
LPN00630X0001A0_C
STEP 8:
Make wiring connections per the
Electrical Connections
section.
STEP 9:
Attach mounting in desired location.
STEP 10:
Tilt luminaire to desired angle and
re-tighten swivel knuckle mount screw.
Tighten to 72 in-lbs ( 8 N
·
m).
2
3
YOKE MOUNT- REQUIRES USE OF
NTF-YM ACCESSORY APPROPRIATE FOR
HOUSING SIZE BEING USED
STEP 1:
Remove (2) #8 screws and (2) 1/4-20 bolts
from sides of luminaire housing. See
Figure 2
.
Discard screws.
STEP 2:
Attach yoke bracket to both sides of the
luminaire using (2) 1/4-20 bolts and
lockwashers supplied with yoke accessory. Do
not fully tighten bolts at this time.
STEP 3:
Aim luminaire in desired direction and attach
yoke to mounting surface using (2) 1/4" (6 mm)
fasteners appropriate for mounting surface.
STEP 4:
Tilt luminaire to desired angle. Lock tilt angle
using the #8 screw (included with yoke)
threaded into the housing on either the left or
right side of the yoke. Tighten screws to
20 in-lbs (2.2 N
·
m).
NOTE:
Notches on the two legs of the
yoke allow for locking at tilt angles in 15°
increments. Notches on one leg of the yoke
lock luminaire at 0°, 30°, 60°, or 90°, while the
notches on the other leg lock the tilt angle at
15°, 45°, or 75°.
STEP 5:
Tighten (2) 1/4-20 yoke bolts to 72 in-lbs
( 8 N
·
m).
STEP 6:
Make wiring connections per the
Electrical
Connections
section.
PHOTOCELL INSTALLATION (ORDERED
SEPARATELY)
STEP 1:
Remove 4 or 6 screws holding back housing to
optical portion of luminaire. See
Figure 3.
STEP 2:
Separate back housing from optical section.
STEP 3:
Remove photocell knockout by striking marked
location on outside wall of housing with a
hammer and punch.
NOTE:
In some housings, driver will need to
be removed from back box before removing
knockout.
STEP 4:
Remove the nut from the threaded nipple of the
photocell.
STEP 5:
Insert the threaded nipple of the photocell
through the wall of the housing. The body of the
photocell and the o-ring on the nipple should
be located on the inside wall of the housing.
STEP 6:
Tighten the nut onto the exposed end of the
threaded nipple to secure the photocell to the
luminaire wall.
STEP 7:
Wire the photocell by following the wiring
instructions included with the photocell.
STEP 8:
If driver was removed in Step 5, reinstall driver
into luminaire housing. Tighten both screws to
20 in-lbs ( 2.2 N
·
m). If driver was not removed,
proceed to Step 9.
STEP 9:
Replace back housing on optical portion of the
luminaire. Be careful not to pinch any leads
during the assembly. Tighten all screws to
20 in-lbs ( 2.2 N
·
m).
Remove the Two
Screws (on Both
Sides of Housing)
to Allow for
Attachment of Yoke
Mount.
Remove these Bolts
(on Both Sides of
Housing) to Allow for
Attachment of Yoke
Mount.
Use 1/4" Screws (Provided by
Others) Here, to Fix the Bracket
to the Mounting Surface
Thread Lead Here
Mounting Bracket
Button Photocell
(Ordered Separately)
Remove the 4 or 6
Screws Here
Back Cover for the Luminaire
Knockout Hole for Button
Photocell (Ordered Separately)
