Credo 4499 Series Installation Manual Download Page 5

Page: 5 / 16

Freephone

0800 487 245

[email protected]

www.trailparts.co.nz

Credo General Installation Instructions

(Applies to Serial # 900 - 4499)

Connect one grey to each side

of the breakaway switch

Green - Right Indicator

Brown - Tail light

White - Earth

Red - Stop light

Yellow - Left Indicator

Connect trailer lights to

5 core output

One 5 Amp/hr battery

must be fitted with the

battery supplied.

Do not use brake system battery

to power any other systems.

There should be no more

than 2.5 metres of cable

between the controller and

the trailer plug to avoid

voltage drop.

Pink

not used

May also be

green

yellow

Battery Requirements:

Electric: 1x5Ah or bigger

Hydraulic: 2x5Ah or 1x12Ah

or bigger

30 amp blade fuse

required on orange wire

Must only be used for

credo connection

Elecrtic Drum magnet

wires are interchangeable

Electric Drum

White to Magnet

Blue to Magnet

Orange Not Used

Wiring diagram below applies to Credo

Brake Controller with electric drums only.

Credo Electric Drum Wiring Diagram

Applies to units in serial

range 900 - 4499

All unused wires must be isolated.

Summary of Contents for 4499 Series

















Search results

Summary of Contents for 4499 Series

Reviews:

Related manuals for 4499 Series

Brands by name

Popular brands

Credo 4499 Series, Installation Manual

Search results

Summary of Contents for 4499 Series

Reviews:

Related manuals for 4499 Series

Brands by name

Popular brands