Creda HBW100FW Instruction Book Download Page 2

Page: 2 / 16

Positioning & Adjusting the feet

Choosing the position of your appliance will influence its performance.

★

Position where possible on a solid floor. Some vibration may occur with a wooden floor.

★

Take care with vinyl floor coverings. The weight of the appliance may cause indentations in
some vinyl floor coverings.

★

For your safety and to comply with IEE regulations, you should not install your appliance in
a bath or shower room. Seek professional advice if you wish to do so.

★

Ensure sufficient space is allowed for the appliance. Dimensions should be a minimum of:-
600mm Wide (23

”), 600mm Deep (23

”) and 900mm High (35

”).

★

Ensure the electrical socket and water taps are easily accessible and that the water supply
can be isolated if necessary.

Your appliance may become noisy or move about the floor if it is not stabilised.

To adjust your appliance it must be in an upright position, then :-

★

Release locking rings on the two front feet.

★

Screw feet in or out until the appliance is standing firm and level.

★

Ensure all feet are in firm contact with the floor.

★

Tighten the locking rings on the front feet.

Dear Customer,

Congratulations on the purchase of your
new ‘Creda’ appliance.
We recommend for your own safety and to
get the best possible results from your
machine that you read through this
handbook thoroughly before using your
appliance for the first time.

★

Transit Brackets MUST be removed
before using the appliance.

★

DO NOT plug in and switch on at the
mains until installation is complete.

Recycling & Disposal Information

As part of Creda’s continued commitment to helping the environ-
ment, Creda may use quality recycled components to keep down
customer costs and minimise material wastage. Please dispose of
packaging and old appliances carefully. To minimise risk of injury to
children, remove the door, plug and cut mains cable off flush with the
appliance. Dispose of seperately to ensure that the appliance can no
longer be plugged into a mains socket.

Electrical Requirements

This appliance should be connected to the mains supply via a suitable switched socket in an
accessible position.

WARNING: This appliance must be earthed.

FUSES

Your appliance comes fitted with a plug and a 13A fuse. If you need to replace the fuse, only
those rated at 13A and ASTA approved to BS1362 should be used. To change fuse, lift holder
to vertical position and lift fuse out. To replace, insert fuse and push fuse holder down into
locked position. Correct replacement is identified by colour coding, or marking on base of
plug.
WARNING: Do not use plug unless fuse holder is in locked position.

CHANGING THE PLUG

Cut off and dispose of the supplied
plug if it does not fit your socket.

WARNING: To avoid a shock haz-
ard do not insert this plug into a
socket anywhere else.

IMPORTANT: WIRES IN THE MAINS
LEAD ARE COLOURED IN
ACCORDANCE WITH THE

FOLLOWING CODE:
Green/Yellow–

Earth

Blue

–

Neutral

Brown

–

Live

If you change the plug, the colour of wires in the mains lead may not correspond with the
colour of the markings identifying terminals in the plug. You should therefore wire it as
shown (see illustration). If the mains lead needs to be replaced at any time, it should be
replaced by a special lead obtainable from your local authorised Creda Service Centre.
A charge will be made if you have damaged the existing lead or require a longer one.
It is strongly advised that this work is carried out by a qualified electrician.

CE marking certifies that this appliance complies with requirements laid down in EEC
Directive 89:336 (Electromagnetic compatibility) and subsequent modifications and Low
Voltage Directive 73/23/EEC.

Green and yellow
(Earth) wire to the
terminal marked
‘E’ or with the
symbol ,
or coloured
green and
yellow.

Brown (Live)

wire to the

terminal

marked ‘L’ or

coloured

red.

Blue (Neutral) wire
to the terminal marked
‘N’ or coloured black.

Cord clamp

13A ASTA
approved

fuse to

BS1362.