background image

Simplicity Bubbler

Crathco

®

9

Daily Cleaning (cont.)

Cleaning Procedures

Cleaning Materials & Tools

Take parts to sink.

4.

Units with spray agitators: 
Remove pump cover and spray
tube.

Lift out dispense valve and
remove o-ring.

Wash with detergent
and warm water.

2.

3.

50°C (122°F) 

Maximum water 

temperature for

cleaning.

75mm (3 inch)

Maximum

water level for

cleaning

Rinse with clean water.

Wipe evaporator plate with 
detergent and warm water.

6.

5.

8.

9.

liquid detergent
(do not use laundry bar/
powdered detergents)

long brush

foam/sponge
(do not use abrasive)

sprayer

toothbrush

sanitizer
(chlorine based)

paper towels

Clean front panel, exterior panels

and release latch.

7.

1.

a.

b.

Clean counter and bottom part
of dispenser with paper towel.

ABRASIVES WILL SCRATCH PLASTIC

PARTS. WASH BOWL LIDS IN COOL OR LUKEWARM WATER TO
AVOID LEAKS DUE TO SEALED SURFACE BEING DAMAGED.

The appliance is not suitable for

installation in an area where a water jet could be used. The
appliance must not be cleaned by water jet

.

THOROUGHLY CLEAN ALL PARTS IN WARM WATER USING A MILD
NON-ABRASIVE DETERGENT AND RINSE THOROUGHLY. 

NOTICE/ AVIS/ AVISO:

NOTICE/ AVIS/ AVISO:

Summary of Contents for Simplicity CS-2D-16

















Reviews: