Draining the Tank (PIC 2/3/4 )
Always empty the tank before shipping.
1. Prepare a heat resistant container to drain the tank water into.
2. Unplug the machine.
3. Remove the drain tray and front access panel. (Figure N)
4. Locate the silicone drain hose on the left side wall. Put the end of the drain hose into the container. Secure
the end of the drain hose (i.e. with tape) into the container. (Figure O)
5. Remove the hose clamp and plug. (Figure P)
6. Allow the tank to drain completely.
NOTE: It may be necessary to pinch the hose and stop the water before container is full. Carefully
re-install plug, then empty container. Repeat steps 4-6 to completely drain tank.
To Prepare for Shipment
Important:
Always completely empty water tank and
POWDER HOPPERS
prior to shipping unit. (See draining the
tank and cleaning the hoppers sections)
NEVER SHIP UNIT WITH POWDER IN HOPPER - THIS WILL CAUSE IRREPARABLE DAMAGE.
Figure N
Figure P
Figure O
Changing the Lightbulb on Models With a Backlit Merchandiser (PIC 1/2/3/4/5/6)
(Refer to Figure M)
(Refer to serial tag to verify model number of your machine)
WARNING:
Disconnect machine from branch electrical supply before changing
the lightbulb.
NOTE: PIC2/3/4 uses a F8T5 12" 8 watt replacement bulb. PIC5/6 uses a 22W circular bulb.
1. All: Remove the front merchandiser photo and cover by grasping the edges of the
merchandiser.
2. PIC1: Lift bulb out of socket vertically.
PIC 2/3/4: Remove the old lightbulb by gently turning the lightbulb 1/4 turn to the left and
pulling the bulb from the socket.
PIC5/6: Disconnect cable from bulb and pull bulb from holder.
3. PIC2/3/4: Install the new bulb by lining up the pins on either end of the bulb parallel
with the socket opening.
4. PIC2/3/4: Gently insert both ends of the bulb into the socket and turn the bulb 1/4 turn to the
right until the bulb locks into place.
5. All: Replace the merchandiser photo and cover.
Figure M
NOTE:
PIC 1 contains 2 gallons of hot water.
PIC 2, PIC 3 and PIC 4 contain 3-1/2 gallons of hot water.
PIC 5 and PIC 6 contain 5-1/2 gallons of hot water.
Service
WARNING: Draining of tank should be performed by a qualified service technician. The tank contains
very hot water. May cause severe burns.
Page 12
Crathco
®
Powdered Beverage Dispensers
Summary of Contents for PIC 1
