Crate V30H Owner'S Manual Download Page 12

Page: 12 / 12

G u i t a r A m p l i f i e r H E A D

V30H TECHNICAL SPECIFICATIONS:

OUTPUT POWER RATING

30 Watts RMS @ 6 % THD, 8 ohm load, 120 VAC

SIGNAL TO NOISE RATIO

71dB Typical

GAIN

Clean 56dB, Overdrive 101dB

TREBLE

12dB range @ 6kHz

BOOST

+10db @ 900Hz

MID

10dB range @ 1kHz

BASS

8dB range @ 150Hz

PRESENCE

+8dB @ 10kHz

PREAMP TUBES

(3) 12AX7A

POWER AMP TUBES

(4) EL84

POWER REQUIREMENTS

120 VAC, 60 Hz, 35VA

100/115 VAC, 50/60 Hz, 35VA

230 VAC, 50/60 Hz, 35VA

SIZE AND WEIGHT

21” W x 7-3/4” H x 8-1/8” D, 25.5 lbs.

The V30H is covered with a durable Tolex material: wipe it clean with a lint-free cloth.

Never spray cleaning agents onto the cabinet. Avoid abrasive cleansers which would damage the finish.

Specifications and information in this manual are subject to change without notice.

www.v-seriesamps.com

47-399-01 • 122104

Summary of Contents for V30H













Search results

Summary of Contents for V30H

Reviews:

Related manuals for V30H

Brands by name

Popular brands

Crate V30H, Owner'S Manual

Search results

Summary of Contents for V30H

Reviews:

Related manuals for V30H

Brands by name

Popular brands