background image

9

Using the Footswitch:

The special Crate four-button footswitch supplied with the RFX200S performs a

variety of functions. The footswitch allows remote channel selection, remote Tap/Save
for each channel, and allows access to an additional DSP preset for each channel of
the amplifier. Use only the supplied Crate four-button momentary footswitch with the
RFX200S. A standard 5-wire midi cable (supplied) may be used to connect the
footswitch to the amplifier.

When the footswitch is connected

to the amplifier, the first tap of but-
tons 1 - 3 select the corresponding
channel. Once a channel is selected,
consequent taps of the same button
produce the same results as tapping
the front panel Save/Tap button – you
can use the footswitch to store pre-
sets and set the tempo of an effect.
(See page 8.)

The “original” DSP presets are

active for each channel when the #4
footswitch LED is illuminated. These
are referred to as “DSP Bank ‘A’.”
When the #4 button is switched and
the LED is off, a second DSP preset
may be stored and recalled for each
channel - “DSP Bank ‘B’.”

NOTE: DSP Bank “B” pre-

sets are only accessible

when the footswitch is

connected to the amplifier.

When the footswitch is not

connected, only DSP Bank

“A” is accessible.

FOOT

SWITCH

SEND

RETURN

SEND 

RETURN

STEREO

EFFECTS LOOP

MONO

EFFECTS LOOP

SWITCH #1:

CH. 1 SELECT;

TAP/SAVE FOR CH. 1

FOOTSWITCH

RFX200 REAR PANEL

5-Conductor

MIDI cable

SWITCH #2:

CH. 2 SELECT;

TAP/SAVE FOR CH. 2

SWITCH #4:

LED on: DSP BANK A
LED off: DSP BANK B

4

2

1

SWITCH #3:

CH. 3 SELECT;

TAP/SAVE FOR CH. 3

3

RFX200S

Three-Channel Guitar Amplifier with Stereo DSP

Summary of Contents for RFX200S

















Reviews: