manualshive.com logo in svg

Crane WEINMAN WE411, Installation And Operation Manual

Share
Download
Crane WEINMAN WE411 Installation And Operation Manual Download Page 4

SECTION: A- PUMP SPECIFICATIONS 

DISCHARGE: 

2" (51mm) NPT, Vertical

TEMPERATURE:

 

104°F (40°C) Continuous.

VOLUTE:

 

Cast Iron, ASTM A-48 Class 30.

MOTOR HOUSING:

Cast Iron ASTM A-48, Class 30.

SEAL PLATE:

 

Cast Iron ASTM A-48 Class 30.

IMPELLER:

 

Design: 

2 Vane, Open, With Pump Out
Vanes On Back Side. Dynamically 
Balanced, ISO G6.3.

Material: 

Zytel 70G43 Nylon, Glass Filled.

SHAFT:

 

416 Stainless Steel.

SQUARE RINGS:

 Buna-N

HARDWARE:

 

300 Series Stainless Steel.

PAINT:

 

Air Dry Enamel

.

SEAL:

 

Design: 

Single Mechanical, Oil-Filled 
Reservoir,
Secondary Exclusion Seal.

Material: 

Rotating Face - Carbon
Stationary Face - Ceramic
Elastomer - Buna-N
Hardware - 300 Series Stainless

CABLE ENTRY:

 

15 ft. (4.5M) Cord w/Plug On 115
Volt, Pressure Grommet For 
Sealing And Strain Relief

.

SPEED:

1750 RPM (Nominal).

UPPER BEARING:

 

Design: 

Sleeve

Lubrication:

Oil

Load:

 Radial

LOWER BEARING:

 

Design:

 

Single Row, Ball

Lubrication:

 Oil

Load:

 

Radial & Thrust

MOTOR: 

Design:

NEMA L Torque Curve. Completely 
Oil-Filled, Squirrel Cage Induction.

Insulation:

 Class 

A. 

SINGLE PHASE:

 

Permanent Split Capacitor (PSC). 
Includes Overload Protection In
Motor.

FLOAT:

Automatic Model. Wide Angle,
Polypropylene, 15ft. (4.5M) Cable.
WE411A, Float w/Plug Attached To 
Discharge Piping, ON and OFF 
Points are Adjustable.

OPTIONAL EQUIPMENT:

 Seal Material, Additional Cable

and Cast Iron Impeller.

WE411A, *WE411, *WE421.
*(Less Float)

inches

(mm)

16.00

(406)

4.00

(102)

10.75

(273)

5.32

(135)

1.56

(40)

3.86

(98)

7.72

(196)

9.00

(229)

120°

Pumping

Differential

4

Summary of Contents for WEINMAN WE411























Reviews:

No comments

Brands by name

Popular brands

Load more brands