Crane STEP1042L Installation And Operation Manual Download Page 4

Page: 4 / 26

SECTION: A- PUMP SPECIFICATIONS

DISCHARGE:

1-1/4" (32mm) NPT, Vertical

LIQUID TEMPERATURE:

104°F (40°C) Continuous.

VOLUTE:

Cast Iron ASTM A-48, Class 30.

MOTOR HOUSING:

Cast Iron ASTM A-48, Class 30.

SEAL PLATE:

Cast Iron ASTM A-48, Class 30.

IMPELLER:

Design:

Single Vane,Enclosed.

Material:

Polypropylene with Threaded 300
Series Stainless Steel Insert,
Dynamically Balanced, ISO G6.3.

SHAFT:

416 Stainless Steel

SQUARE RINGS:

Buna-N

HARDWARE:

300 Series Stainless Steel

PAINT:

Air Dry Enamel.

SEAL:

Design:

Tandem Mech,Oil Filled Reservoir.

Material:

Rotating Face - Carbon
Stationary Face - Ceramic
Elastomer - Buna-N
Hardware - 300 Series Stainless

CABLE ENTRY:

15ft. (4.5M) Cord. Pressure Grommet
For Sealing And Strain Relief

SPEED:

3450 RPM (Nominal).

UPPER BEARING:

Design:

Sleeve

Lubrication:

Oil

Load:

Radial

LOWER BEARING:

Design:

Single Row, Ball

Lubrication:

Oil

Load:

Radial & Thrust

MOTOR:

Design:

NEMA L-Single Phase, NEMA B-Three
Phase Torque Curve. Completely
Oil-Filled, Squirrel Cage Induction.

Insulation:

Class

SINGLE PHASE:

Permanent Split Capacitor (PSC).
Includes Overload Protection
In Motor.

THREE PHASE:

Dual Voltage 230/460;
Requires Overload Protection to be
Included in Control Panel.

OPTIONAL EQUIPMENT:

Seal Materials, Impeller Trims, N/O

Moisture Sensors (Requires Relay in Control Panel), N/C
Temperature Sensor with Cable for 3 Phase Pumps (Requires
Relay in Control Panel), Additional Cable, CSA Listing on 3 phase
pumps.

inches

(mm)

19.44

(494)

11.72

(298)

5.87

(149)

4.62

(117)

9.25

(235)

3.44

(87)

1-1/4" (32) NPT

DISCH.

1.22

(31)

Summary of Contents for STEP1042L



























Search results

Summary of Contents for STEP1042L

Reviews:

Related manuals for STEP1042L

Brands by name

Popular brands

Crane STEP1042L, Installation And Operation Manual

Search results

Summary of Contents for STEP1042L

Reviews:

Related manuals for STEP1042L

Brands by name

Popular brands