Crane NRI Currenza C2 Technical Documentation Manual Download

Page: 40 / 83

National Rejectors, Inc. GmbH, Buxtehude

Configuration

hanGe

payouT

Change payout

This chapter describes how to adapt the change payout to the machine

environment:

Reassigning coin cassette

•

Limiting change return (only c

•

BDV/Executive)

Configuring conditions for tube empty message

•

(only c

BDV/Executive)

Activating low-power single-motor payout

•

Reassigning coin cassette

If you exchanged the change tubes or coin cassette, in order to be able

to pay out other or more coins, the new sorting must be set in the coin

changer.
The coin changer comes with pre-programmed coin cassette combinations,

which can be selected depending on the new sorting.
If the new tube combination is not part of the pre-programmed combinations,

it may be configured manually

Summary of Contents for NRI Currenza C2




















































































Search results

Summary of Contents for NRI Currenza C2

Reviews:

Related manuals for NRI Currenza C2

Brands by name

Popular brands

Crane NRI Currenza C2, Technical Documentation Manual

Search results

Summary of Contents for NRI Currenza C2

Reviews:

Related manuals for NRI Currenza C2

Brands by name

Popular brands