Please Read This Before Installing Or Operating
Pump. This information is provided for
SAFETY
and
to
PREVENT EQUIPMENT PROBLEMS.
To help
recognize this information, observe the following
symbols:
IMPORTANT!
Warns about hazards that can
result in personal injury or Indicates factors
concerned with assembly, installation,
operation, or maintenance which could result
in damage to the machine or equipment if
ignored.
CAUTION!
Warns about hazards that
can or will
cause minor
personal injury or property damage if
ignored. Used with symbols below.
WARNING!
Warns about hazards that can or
will cause serious personal injury, death, or major
property damage if ignored. Used with symbols
below.
Only qualifi ed personnel should install, operate and
repair pump. Any wiring of pumps should be performed
by a qualifi ed electrician.
WARNING !
To reduce risk of electrical
shock, pumps and control panels must
be properly grounded in accordance with
the National Electric Code (NEC) or the
Canadian Electrical Code (CEC) and all
applicable state, province, local codes
and ordinances. Improper grounding voids
warranty.
WARNING!
To reduce risk of electrical
shock, always disconnect the pump from
the power source before handling or
servicing. Lock out power and tag.
WARNING!
Operation against
a closed discharge valve will
cause premature bearing and
seal failure on any pump, and
on end suction and self priming pump the heat build
may cause the generation of steam with resulting
dangerous pressures. It is recommended that a high
case temperature switch or pressure relief valve be
installed on the pump body.
CAUTION !
Never operate a pump with a
plug-in type power cord without a ground
fault circuit interrupter.
CAUTION !
Pumps build up heat
and pressure during operation-
allow time for pumps to cool
before handling or servicing.
WARNING !
Do not pump hazardous
materials (fl ammable, caustic, etc.) unless
the pump is specifi cally designed and
designated to handle them.
CAUTION !
Do not
block or restrict discharge
hose, as discharge hose may whip under
pressure.
WARNING !
Do not wear loose clothing
that may become entangled in moving
parts.
WARNING !
Keep clear of suction and
discharge openings.
DO NOT
insert fi ngers
in pump with power connected.
Always wear eye protection when working
on pumps.
Make sure lifting handles are securely
fastened each time before lifting.
DO NOT
operate pump without safety devices in
place. Always replace safety devices that
have been removed during service or repair.
Secure the pump in its operating position so
it can not tip over, fall or slide.
DO NOT
exceed manufacturers
recommendation for maximum
performance, as this could cause the motor
to overheat.
DO NOT
remove cord and strain relief.
DO NOT
connect conduit to pump.
WARNING !
Cable should be protected at all
times to avoid punctures, cut, bruises and
abrasions. Inspect frequently. Never handle
connected power cords with wet hands.
W
ARNING !
To reduce risk of electrical
shock, all wiring and junction connections
should be made per the NEC or CEC
and applicable state or province and local
codes. Requirements may vary depending
on usage and location.
WARNING!
Submersible Pumps are not
approved for use in swimming pools,
recreational water installations decorative
fountains or any installation where human
contact with the pumped fl uid is common.
WARNING!
Products returned must be
cleaned, sanitized, or decontaminated
as necessary prior to shipment, to insure
that employees will not be exposed to
health hazards in handling said material.
All Applicable Laws And Regulations Shall
Apply.
Bronze/brass and bronze/brass fi tted
pumps may contain lead levels higher than
considered safe for potable water systems.
Lead is known to cause cancer and birth
defects or other reproductive harm. Various
government agencies have determined that
leaded copper alloys should not be used in
potable water applications. For non-leaded
copper alloy materials of construction,
please contact factory.
Crane Pumps & Systems, Inc. is not
responsible for losses, injury, or death
resulting from a failure to observe these
safety precautions, misuse or abuse of
pumps or equipment.
SAFETY FIRST!
Hazardous
fl uids can
cause fi re or
explosions,
burns or death
could result.
Extremely hot
- Severe burns
can occur on
contact.
Biohazard can
cause serious
personal injury.
Hazardous fl u-
ids can Hazard-
ous pressure,
eruptions or ex-
plosions could
cause personal
injury or prop-
erty damage.
Rotating
machinery
Amputation
or severe
laceration
can result.
Hazardous volt-
age can shock,
burn or cause
death.
Other brand and product names are trademarks or registered trademarks of their respective holders.
® Barnes is a registered trademark of Crane Pumps & Systems, Inc.
2002, 2003, 6/2004, 5/06, 9/06
Alteration Rights Reserved
RECOMMENDED INSTALLATION
1. LOCATION:
This unit is self-contained
and is recommended for use beneath
a sink or to collect condensate. This
unit shall NOT be installed in locations
classifi ed as hazardous in accordance
with the National Electrial Code (NEC),
ANSI/NFPA 70 or the Canadian Electrical
Code (CEC). The unit shall be vented in
accordance with local plumbing codes.
The unit shall be installed on a fi rm, level
surface.
2. DISCHARGE:
Discharge pipe should
be as short as possible. This unit has a
self-contained check valve. No additional
check valve is required.
3. VENT:
Do not use an automatic
plumbing vent device.
4. GENERAL:
Always disconnect the unit
from the electrical power source before
handling.
Plug the unit into a CFGI receptacle.
5. TEST OPERATIONS:
One cycle of
operation should be observed so that
any potential problems can be corrected.
TROUBLE SHOOTING
CAUTION!
Always disconnect the unit from the
electrical power source before handling. If the system
fails to operate properly, carefully read instructions and
perform maintenance recommendations.
If operating problems persist, the following chart may
be of assistance in identifying and correcting them:
MATCH “CAUSE” NUMBER WITH
CORRELATING “CORRECTION” NUMBER
.
NOTE:
Not all problems and corrections are included.
PROBLEM
CAUSE
CORRECTION
Pump will not
run
1. Poor electrical
connection, blown fuse,
tripped breaker or other
interruption of power,
improper power supply.
2. Float is damaged,
dislocated.
3. Insuffi cient liquid level.
1. Check
all electrical
connections for
security. Check
for blown fuses,
tripped circuit
breakers or tripped
GFCI outlets.
2. Claim the
damage through
the carrier and
arrange for a
replacement unit.
3. Make sure liquid
level is at least
equal to suggested
turn-on point.
4. Recheck all
sizing calculations
to determine proper
pump size.
5. Check discharge
line for restrictions,
including ice if line
passes through or
into cold areas.
6. Replace with a
new check valve.
7. Open valve.
8. Clean impeller
and inlet of any
obstruction.
9. Check pump
temperature limits
& fl uid temperature.
10. Replace portion
of discharge
pipe with fl exible
connector.
11. Check for leaks
around basin inlet
and outlets.
Pump will not
turn off
2. Float is damaged,
dislocated.
4. Excessive infl ow or
pump not properly sized
for application.
Pump hums but
does not run
1. Incorrect voltage
8. Impeller jammed or
inlet plugged.
Pump delivers
insuffi cient
capacity
1. Incorrect voltage.
4. Excessive infl ow or
pump not properly sized
for application.
5. Discharge restricted.
6. Check valve stuck.
7. Shut-off valve closed.
8. Impeller jammed or
damaged, inlet plugged.
Pump cycles
too frequently
6. Check valve stuck.
11. Clean the basin and
inlet of any obstruction.
Pump shuts off
and turns on
independent of
switch, (trips
thermal overload
protector).
CAUTION!
Pump may start
unexpectedly.
Disconnect
power supply.
1. Incorrect voltage.
4. Excessive infl ow or
pump not properly sized
for application.
8. Impeller jammed,
damaged, inlet plugged.
9. Excessive water
temperature.
Pump operates
noisily or
vibrates
excessively
5. Discharge restricted.
8. Impeller broken.
10. Piping attachments to
building structure too rigid
or too loose.
Limited 24 Month Warranty
Crane Pumps & Systems warrants that products of our manufacture
will be free of defects in material and workmanship under normal
use and service for twenty-four (24) months after manufacture date,
when installed and maintained in accordance with our instructions.
This warranty gives you specifi c legal rights, and there may also be
other rights which vary from state to state. In the event the product
is covered by the Federal Consumer Product Warranties Law (1) the
duration of any implied warranties associated with the product by virtue
of said law is limited to the same duration as stated herein, (2) this
warranty is a LIMITED WARRANTY, and (3) no claims of any nature
whatsoever shall be made against us, until the ultimate consumer, his
successor, or assigns, notifi es us in writing of the defect, and delivers
the product and/or defective part(s) freight prepaid to our factory or
nearest authorized service station. Some states do not allow limitations
on how long an implied warranty lasts, so the above limitation may
not apply.
THE SOLE AND EXCLUSIVE REMEDY FOR BREACH OF
ANY AND ALL WARRANTIES WITH RESPECT TO ANY PRODUCT
SHALL BE TO REPLACE OR REPAIR AT OUR ELECTION, F.O.B.
POINT OF MANUFACTURE OR AUTHORIZED REPAIR STATION,
SUCH PRODUCTS AND/OR PARTS AS PROVEN DEFECTIVE.
THERE SHALL BE NO FURTHER LIABILITY, WHETHER BASED
ON WARRANTY, NEGLIGENCE OR OTHERWISE.
Unless expressly
stated otherwise, guarantees in the nature of performance specifi cations
furnished in addition to the foregoing material and workmanship
warranties on a product manufactured by us, if any, are subject
to laboratory tests corrected for fi eld performance. Any additional
guarantees, in the nature of performance specifi cations must be in writing
and such writing must be signed by our authorized representative. Due
to inaccuracies in fi eld testing if a confl ict arises between the results of
fi eld testing conducted by or for user, and laboratory tests corrected for
fi eld performance, the latter shall control.
RECOMMENDATIONS FOR
SPECIAL APPLICATIONS OR THOSE RESULTING FROM SYSTEMS
ANALYSES AND EVALUATIONS WE CONDUCT WILL BE BASED ON
OUR BEST AVAILABLE EXPERIENCE AND PUBLISHED INDUSTRY
INFORMATION. SUCH RECOMMENDATIONS DO NOT CONSTITUTE
A WARRANTY OF SATISFACTORY PERFORMANCE AND NO SUCH
WARRANTY IS GIVEN.
This warranty shall not apply when damage is caused by (a) improper
installation, (b) improper voltage (c) lightning (d) excessive sand or
other abrasive material (e) scale or corrosion build-up due to excessive
chemical content. Any modifi cation of the original equipment will also
void the warranty. We will not be responsible for loss, damage or labor
cost due to interruption of service caused by defective parts. Neither
will we accept charges incurred by others without our prior written
approval.
This warranty is void if our inspection reveals the product was used in
a manner inconsistent with normal industry practice and/or our specifi c
recommendations. The purchaser is responsible for communication
of all necessary information regarding the application and use of the
product.
UNDER NO CIRCUMSTANCES WILL WE BE RESPONSIBLE
FOR ANY OTHER DIRECT OR CONSEQUENTIAL DAMAGES,
INCLUDING BUT NOT LIMITED TO TRAVEL EXPENSES, RENTED
EQUIPMENT, OUTSIDE CONTRACTOR FEES, UNAUTHORIZED
REPAIR SHOP EXPENSES, LOST PROFITS, LOST INCOME, LABOR
CHARGES, DELAYS IN PRODUCTION, IDLE PRODUCTION, WHICH
DAMAGES ARE CAUSED BY ANY DEFECTS IN MATERIAL AND/
OR WORKMANSHIP AND/OR DAMAGE OR DELAYS IN SHIPMENT.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER EXPRESS
OR IMPLIED WARRANTY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
.
No rights extended under this warranty shall be assigned to any other
person, whether by operation of law or otherwise, without our prior
written approval.
