Page 5
4.9
Power Saving
The fitness watch offers a power saving function. The display
is turned off to prolong the life span of the battery.
To activate the power saving function, press the „SELECT“
key in the time mode for approx. 5 seconds. The display is
turned off. In doing so, the individual mode settings are NOT
deleted.
Press any key to stop the power saving and switch the display
back on.
4.10
Display Light
By pressing the LIGHT key the display is lit for approx. 4
seconds to allow you to read the display of the fitness watch in
the darkness. It is not possible to keep the display light turned
on. Please be aware that the use of the display lightening
requires more energy, resulting in a shorter life span of the
battery.
4.11
Specifications
Battery
1 x 3 V Battery type CR2032
(1 x 3 V
0.5 mA CR2032)
Stopwatch
* Meas. range:
* Accuracy:
99 hrs 59 min. 59 sec.
1/100 second
(up to 59 min. 59.99 sec.)
Pulse
* Meas. range:
* Accuracy:
40 to 240 bpm (beats/minute)
1 bpm
Steps
0 – 99,999 steps
Calories
0 – 9999 kcal
Fatburning
0 – 1298 g
Distance
0 – 93.17 miles
Speed
max. 40.7 miles per hour
Pace
max. 39 min. 59 sec.
Training time
max. 9 hrs. 59 min. 59 sec.
Countdown
max. 9 hrs. 59 min. 59 sec.
4.12
Battery Change
To guarantee the water resistance of your fitness watch the
battery change should be carried out by a watch professional
or a service centre to avoid damage to the sealing ring and
case.
Symbol image
If you still want to change the battery
yourself please follow the instructions
below:
Unscrew the four screws on the back
cover on the fitness watch with a
screwdriver. Open the battery
compartment by carefully lifting the
locking clip with the screwdriver over
the locking hook.
Insert a new battery CR2032 (3 V)
with the plus polarity (+) facing
upwards. Then hook the battery fastener back into place and
screw the cover back on.
Caution: There is a plastic insert between the electronics and
the cover, displaying the required battery type for the fitness
watch. Be aware not to lose this plastic insert when changing
the battery.
If the display shows irregular symbols please take the battery
out and reinsert it. This will reset the microprocessor. After
the reset the fitness watch should be back to functioning as
usual.
Note:
Please be aware that all personal data will need to be
reset after changing the battery.
5
Conformity
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
NOTE: This equipment has been tested and found to comply
with the limits of a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and
receiver.
•
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician
for help.
WARNING: changes or modifications to this unit not
expressly approved by the party responsible for compliance
could void user's authority to operate the equipment.
Company Krippl-Watches
Telephone number: please refer to the information given in
the warranty card
6
Troubleshooting/FAQs
Before submitting a claim about the fitness watch, please
check the battery and change it if required.
How to make a claim:
Please inform us about the article
number of the product and the reason of the claim (email).
Additionally, you can refer to the FAQ section on our online
product service page for further help with your fitness watch.
http://www.produktservice.info EAN: 20009212
Why is the distance display of my distance covered not
correct?
Have you set the step lengths for walking and running? For
optimal results, the step length for both „walking“ and also
„running“ must be set. Shuffling gait, poor footwear and
uneven surfaces may result in incorrect measurements. When
climbing stairs or hills the distance measurement is reduced as
the watch has only been designed for activities on
even
surfaces. Apply the same pace when walking or running as
when calculating the step length. Please be aware that the
measurements can be imprecise/irregular for less active people
What shall I do if my weight changes?
Insert the new weight as the once set weight will be saved until
it is changed.
How is the calorie output measured?
The calorie output mainly depends on the number of steps and
the body weight (insert correct body weight!).
The pulse display is not working or is not correct - why?
Under certain circumstances it may happen that the pulse
cannot be measured on some people or it may be very difficult:
•
Your pulse is below 40 beats per minute.
•
Your heart only emits very weak signals
Please also refer to the grey information box in point 4.8.1
„Pulse Measurement”.
What can cause the display of my fitness watch to stop
reacting.
If the display is “frozen“ or it shows irregular symbols:
Take the battery out and reinsert it. This will reset the
microprocessor.
After the reset, the fitness watch should be back to functioning
as usual.
The display is weak, hardly legible – what can I do?
Replace the battery as soon as the display starts to diminish or
when it is fully faded. Always ensure the battery polarities are
aligned correctly. When the battery is removed and reinserted
the personal data must be reset.
Why is the display light not working?
The battery might be flat? Please check the battery and replace
with a new one (3 V/CR2032) if it is flat. Check the +/-
polarity.
