User manual
SPEED & CADENCE SENSOR
GB
IRE
AFTER SALES SUPPORT
96044
YEAR
WARRANTY
GB
00800 52323000 00800 52323000
[email protected]
MODEL:
AE8-SPCD-2 09/2018
PRODUCED IN CHINA FOR:
ALDI STORES LTD. PO BOX 26, ATHERSTONE
WARWICKSHIRE, CV9 2SH
ALDI STORES (IRELAND) LTD.
PO BOX 726, NAAS, CO. KILDARE.
Visit us at www.aldi.com
IRE
Great care has gone into the manufacture of this product and it should therefore provide you
with years of good service when used properly.
In the event of product failure within its intended use over the course of the first 3 years after
date of purchase, we will remedy the problem as quickly as possible once it has been brought
to our attention. In the unlikely event of such an occurrence, or if you require any information
about the product, please contact us via our helpline support services, details of which are to
be found both in this manual and on the product itself.
Dok./Rev.-Nr. AE8-SPCD-2_BA_V5
3V
CR2032
1
2
3
4
5
6
7
8
9
9
10
4
3
11
6
5
3
2
1
9
3
1
9
A
B
D
C
2 mm max.
8
7
1
1
5
PACKAGE CONTENTS/DEVICE PARTS
1
Speed & cadence sensor (see
fig. A, fig. B, fig. C, fig. D
)
2
Sensor cover (see
fig. A, fig. B
)
3
Cable ties, 6x (see
fig. A, fig. B
)
4
Cadence magnet (see
fig. A, fig. B
)
5
Speed magnet (see
fig. A, fig. B, fig. C
)
6
Holder for speed magnet (see
fig. A, fig. B
)
7
Battery CR2032 (already inserted) (see
fig. A, fig. D
)
8
Cover for battery compartment (see
fig. A, fig. D
)
9
Opening (for cable ties) of the speed & cadence sensor (see
fig. A, fig. B
)
10
Arrow marks (see
fig. A, fig. B
)
11
Opening (for cable ties) of the cadence magnet (see
fig. A, fig. B
)
GENERAL INFORMATION
Reading and storing the user manual
This user manual accompanies this speed & cadence sensor. It contains
important information on setup and use.
Before using the speed & cadence sensor, read the user manual carefully. This
particularly applies to the safety instructions. Failure to follow this user manual may
result in severe injury or damage to the speed & cadence sensor. The user manual is
based on the standards and rules in force in the European Union. When abroad, you
must also observe country-specific guidelines and laws. Store the user manual for
future use. Make sure to include this user manual when passing the speed & cadence
sensor on to third parties.
Explanation of symbols
The following symbols and signal words are used in this user manual, on the speed &
cadence sensor or on the packaging.
WARNING!
This signal symbol/word designates a hazard with moderate degree of risk which may
lead to death or severe injury if not avoided.
NOTICE
This signal word warns against potential damages to property.
This symbol provides you with useful supplementary information on
assembly or operation.
Declaration of conformity (see chapter “Declaration of conformity”):
Products marked with this symbol meet all applicable EU Directives for the
European Economic Area.
IPX7
The speed & cadence sensor is protected against immersion, up to 1 m
depth for up to 30 minutes.
Google Play™ and Android™ are trademarks of Google Inc. Apple, the Apple logo, iPad
and iPhone are trademarks of Apple Inc., registered in the USA and other countries. App
Store is a service mark of Apple Inc. The Bluetooth® word mark and logos are registered
trademarks of Bluetooth SIG, Inc. and are used under licence by Krippl-Watches. Other
trademarks and brand names are the property of their respective owners.
SAFETY
Proper use
The speed & cadence sensor is exclusively designed for measuring your speed and
cadence and for exchanging data with smartphones and tablets. It is designed for
collecting data for analysis with the Crane Connect app. You can use this data to help
you reach your goals in terms of fitness.
The speed & cadence sensor is only intended for private use and is not suitable for
commercial applications. It is not a children’s toy. Only use the speed & cadence sensor
as described in this user manual. Any other use is deemed improper and may result in
damage to property or even personal injury. The manufacturer or vendor accepts no
liability for damage caused by improper or incorrect use.
Safety instructions
WARNING!
Danger of suffocation!
The speed & cadence sensor contains a battery and small parts. While playing, children
could swallow batteries, small parts, or package wrappings and choke.
•
Keep the batteries, small parts, and package wrappings away from children.
•
If a battery or small parts are swallowed, seek immediate medical attention.
• Keep the speed & cadence sensor out of the reach of children.
WARNING!
Danger for children and persons with impaired physical, sensory
or mental capacities (e.g. partially disabled persons, older persons
with reduced physical and mental capacities) or lack of experience
and knowledge (e.g. older children).
This speed & cadence sensor is not intended for use by persons
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the speed & cadence sensor by a
person responsible for their safety. Children must not play with the
speed & cadence sensor. Cleaning and user maintenance may not
be performed by children unless they are under supervision.
• Keep children away from the speed & cadence sensor.
• Do not let children play with the packaging wrapper. They
could swallow it and suffocate.
Further information and this user manual can be found at www.krippl-watches.com
(under “Customer Service”).
NOTICE
Risk of damage!
Improper handling of the speed & cadence sensor may result in damage to the speed &
cadence sensor. You can use the speed & cadence sensor at ambient temperatures between
0 °C and +50 °C. Do not expose the speed & cadence sensor to permanent moisture.
Avoid dust, heat and continuous exposure to direct sunlight. Never try to repair the
speed & cadence sensor yourself. For technical problems, contact the service address
indicated on the warranty card.
Avoid strong magnetic fields (e.g. transformers). Otherwise, this may cause
fluctuations in the transmission of the data measured.
WARNING!
Risk of explosion and chemical burns!
Improper handling of batteries poses the risk of explosions or chemical burns caused by
leaking battery acid.
•
Never expose the batteries to excessive heat, such as sunlight,
fire or similar – increased risk of leakage!
•
Do not charge or reactivate the batteries, do not disassemble
them, do not dispose of them in fire and do not short circuit
them.
•
Batteries may pose a risk to health if ingested. You should
therefore store the batteries so that they are not accessible to
children. If you suspect that a battery has been swallowed or
otherwise incorporated, seek immediate medical attention.
•
If batteries leak, use gloves to remove them. Afterwards, clean
the battery compartment with a cloth without water or any
cleaners.
•
Only have the battery replaced with the same battery type.
•
Do not allow battery acid to come into contact with skin, eyes
or mucus membranes. In the event of contact with battery acid,
immediately flush the applicable areas with plenty of clean
water and consult a doctor if necessary.
•
Dispose of batteries at your collection point.
•
Keep the user manual for battery information.
•
Further notes and information on changing the battery can be found in the chapter
“Changing the battery”.
CHECKING THE SPEED & CADENCE SENSOR AND PACKAGE
CONTENTS
NOTICE
Risk of damage!
If you are not cautious when opening the packaging with a sharp knife or other pointed
objects, you may damage the speed & cadence sensor.
–
Be careful when opening the package.
1. Remove the speed & cadence sensor
1
from the packaging. Remove the
packaging material and protective labels from the speed & cadence sensor. Keep
the packaging materials away from children and dispose of the materials in an
environmentally friendly manner.
2. Check whether the product contents are complete and if the speed & cadence
sensor is damaged or not (see
fig. A
).
3.
If the delivery is incomplete and/or if parts are damaged, do not use the speed &
cadence sensor. Contact the manufacturer via the service address indicated on the
warranty card.
FUNCTIONS
You can use the speed & cadence sensor to measure/record your speed and cadence
during a workout.
This data is transmitted to a device, e.g. your smartphone. The free Crane Connect app
allows you to analyse this data in depth. Once installed, the Crane Connect app will
provide you with the following information regarding your workout:
•
Duration of workout
• Distance covered
• Cadence measurement
• Speed measurement
•
Lap times
•
Calorie consumption
• Route map
COMPATIBLE BLUETOOTH® DEVICES
The following devices with Bluetooth® 4.0 or higher are compatible with the speed &
cadence sensor
1
and the Crane Connect app:
• Apple® iPhone® 4s and more recent versions
•
Apple® iPad® 3rd generation and more recent versions
• Apple® iPad mini™
• Apple® iPad Air™ and more recent versions
•
Smartphones and tablets with Android™ 4.3 and more recent versions
You can find a complete list of supported devices online at
www.cranesportsconnect.com/compatibility.
CRANE CONNECT APP
Downloading and installing the Crane Connect app
For using the speed & cadence sensor
1
you must download the Crane Connect app
and install it on your compatible Bluetooth® device.
–
Download the free Crane Connect app from the App Store, from the Google Play
Store, at www.cranesportsconnect.com under the “Download” tab or via the
following QR codes.
QR code for Android
QR code for iOS
To avoid long download times and the associated costs, it is recommended
that you use a Wi-Fi connection for downloads.
–
Install the Crane Connect app on your compatible Bluetooth® device. Follow the
step-by-step instructions for this.
Creating a user account
To create a user account with the Crane Connect app, proceed as follows:
1. Start the Crane Connect app.
2.
Follow the registration instructions step by step.
3. To perform user and product-specific settings, select the icon “All Settings”.
You can also create new users on the website www.cranesportsconnect.
com.
Connecting the speed & cadence sensor with the Crane Connect
app
Make sure that the Bluetooth® function on your smartphone has been
activated.
1.
Once the user settings are complete, return to the “All Settings” menu.
2.
Select the icon “Speed & Cadence Sensor”.
You can change the settings for optimal use of your speed & cadence sensor.
3.
To connect the speed & cadence sensor
1
with your smartphone, select
“Connect” in the “Pairing” field.
A notification window will appear.
4.
In this window, press “Pair now”.
The speed & cadence sensor will connect automatically to the app
We would recommend to take either the speed magnet
5
or the
cadence magnet
4
and move it across the corresponding arrow mark
10
on the speed & cadence sensor
1
, with a maximum distance
of approx. 2 mm between speed & cadence sensor and magnet during the
connection process.
5.
From there, you can start the measurements and access the analyses of your
measured data via the “Speed & Cadence Sensor” icon.
As soon as you have connected the speed & cadence sensor with the Crane
Connect app, all measured data will be transferred to it.
