background image

- 63 -

IX - OPERATING FAULTS

Display

Description

Solution

Outside sensor fault

Check that the sensor is correctly fitted and 
connected

Boiler sensor 1 fault

Check that the sensor is correctly fitted and 
connected

Flue gas detector fault

Check that the sensor is correctly fitted and 
connected

Flow sensor 2 fault

Check that the sensor is correctly fitted and 
connected

Return sensor 1 fault

Check that the sensor is correctly fitted and 
connected

Domestic hot water sensor 1 fault

Check that the sensor is correctly fitted and 
connected

Domestic hot water sensor 2 fault

Check that the sensor is correctly fitted and 
connected

Room device 1 faulty

Check the boiler connections

Room device 1 error or radio clock error

Check compatibility of the room device or 
clock

Water pressure sensor fault

Increase the pressure in the circuit 

 

(if P < 0.2 bar), check the connections of the 
pressure sensor

Short-circuit on LPB or no voltage

Check the wiring

Two identical addresses on the LPB 

Check the addressing

Loss of data in the EEPROM

Change the LMU

Component fault in the LMU

Change the LMU

Two master clocks (only one normally), 
programming problem

Check parameter 96 of the QAA73 (only one 
device can have the message “QAA73”)

STB (boiler overheating safety) activated

Check that shunt X3-01 is present and 
whether the installation water flow is sufficient 
(circulating pump, isolation valve, etc.) 

Response of the safety thermostat

Check whether the installation water flow is 
sufficient (circulating pump, isolation valve, 
etc.) 

Flue gas alarm displayed (problem of the 
flue gas temperature being too high)

Check whether the boiler is not on thermal 
overload or that the exchanger is not clogged

Water pressure too high

Check and adjust the pressure level if 
necessary with P < 4 bar

Water pressure too low

Check and adjust the pressure level if 
necessary with P > 0.4 bar

Maximum flue gas temperature exceeded

Check whether the boiler is not on thermal 
overload or that the exchanger is not clogged

Summary of Contents for THI 5-25c



































































Reviews: