Follow these precautions when using a battery in this device:
1. Use only the size and type of battery specified.
6. Do not dispose of battery in fire. Battery may explodes or leak.
7. Clean the battery contacts and also those of the device prior to battery installation.
2. Be sure to follow the correct polarity when installing the battery as indicated
in the battery compartment. A reversed battery may cause damage to the device.
4. If the batteries in the device are consumed or the device is not to be used
for a long period of time, remove the batteries to prevent damage or injury
from possible battery leakage.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc)
or old batteries with fresh ones.
5. Do not try to recharge the battery not intended to be recharged; it can overheat
and rupture. (Follow battery manufacturer’s instructions.)
BATTERY PRECAUTIONS
DC OPERATION
To operate the unit using AC power, connect the plug from the supplied AC/DC
Adaptor to the DC IN Jack on the rear of unit. Plug the AC/DC Adaptor to the AC
wall outlet having AC 100-240V~, 50/60 Hz.
To use battery power, make sure the plug was detached off from the DC IN Jack.
Note:
When the plug was inserted to the DC IN Jack, battery power will be cut off
automatically.
To set or reset the actual time:
1.Make sure the unit is in power off (standby) mode before setting.
2.Press and hold the MEM/SET Button on the front of unit until the digit of hour on
the display is blinking. Press the or Button to set the hour. (Make sure the
PM Indicator on the display is lit if the time is PM and not light if the time is AM).
3.Press the MEM/SET Button again; the digit of minute on the display will blink.
Press the or Button to set the Minute.
4.When finished, press the MEM/SET Button to save the settings and exit.
OPERATION
Radio reception
1.Press the POWER/FUNC Button to turn on the unit.
2.Press the POWER/FUNC Button repeatedly until Radio frequency appears on the display.
Wait a few seconds, you will hear sounds from speakers.
3.Press and hold the or Button until the displayed frequency starts running then release
4.Repeat procedure 3 until the desired radio station was found.
5.Adjust the volume to the desiredd level by pressing VOL+/AL 1 or VOL–/AL 2 Button.
6.To power off (Standby mode) the unit, press and hold the POWER/FUNC Button until "OFF"
appear on the display then release the button.
ANTENNA:
The Antenna wire on the rear cabinet is for radio reception. If reception is weak, unwind and
extend the wire or relocate the wire to improve the radio reception.
RADIO STATION PRESETTING
1.Received the desired radio station as the previous procedure.
2.Press the MEM/SET Button, "P XX" (XX is the last stored number of radio station) will appear on
the display and "XX" will be blinking. Press the or Button repeatedly to select the
desired location (P01 – P20) you want store to. Press the MEM/SET Button again to store.
3.Repeat the same procedure until all the desired radio stations were stored into the memory.
4.After settings, press the CH MODE Button to enter to Channel mode. "P XX" will appear on the
display. Press the or Buttons repeatedly to select the desired stored radio station.
Notes:
If AC/DC Adaptor has been unplugged from the wall outlet or
the preset radio stations will be deleted.
The stored radio station only can be deleted by storing another new radio station.
Total 20 radio stations can be stored in the memory list.
In first time use or re-pairing to new BT Device, pairing the unit to external
BT (BLUETOOTH) PAIRING AND OPERATION
BT Device as follows:
1. Press the POWER/FUNC Button to turn on the unit.
2. Press the POWER/FUNC Button repeatedly until “bt” appears on the display.
3. Power on the external BT Device and enter to search mode. Start pairing as
the on screen instructions on the external BT Device. (For details pairing
procedures, please refer to the user’s manual of your BT Device.)
4. When the external BT Device searched the unit, our model number
“CMA 3542” will appear on the display of external BT Device.
5. Pairing code “0000” may need to enter.
1. Turn on the BT function of the external BT Device.
2. Press the POWER/FUNC Button to turn on the unit.
4. Plays the music in the connected BT Device as usual.
5. During playback:
Press the VOL (Volume) + or – Buttons to adjust volume level.
Press the Button to pause; press again to resume normal playback.
Press the / Button to skip tracks.
3. Press the POWER/FUNC Button repeatedly until “bt” appears on the display.
Wait a few seconds until the unit paired to the external BT Device automatically.
(When paired, a melody will heard from speakers) .
6. To power off (Standby mode), press and hold the POWER/FUNC Button
until "OFF" appear on the display then release the button.
Normal operation after pairing
To listen to the music from the external audio device, iPhones, iPads or iPods as follows:
1.Connect the external audio device or iPods/iPhone by an audio connection cable with 3.5mm
stereo plug on both ends (Cable not included).
2.Insert one end to the AUX Jack on the rear of unit. Insert the other end to the Phones Jack;
Line Out Jack or AUX Out Jack on the external audio device or iPods.
3.Press the POWER/FUNC Button to turn on the unit.
4.Press the POWER/FUNC Button repeatedly until “AU” appears on the display.
5.Playback the music in the connected external audio device or iPods as usual.
6.Press VOL+ or VOL– Button on the unit (and the connected unit) to adjust volume level as
desired.
7.To power off (Standby mode) the unit, press and hold the POWER/FUNC Button until "OFF"
appear on the display, then release the button.
AUX IN
ALARM SETTING
Alarm 1 setting:
1.Make sure the unit is in power off (standby) mode before setting.
2.Press and hold the VOL +/AL 1 Button until AL 1 indicator lit
and Alarm 1 time appears on the display (The digit of hour will be blinking).
3.Press the or Buttons repeatedly to set the hour. (Make sure the PM Indicator on the
display is light if the alarm 1 time is PM and not light if it is AM).
4.Press the VOL +/AL 1 Button again, the digit of minute will be blinking. Press the or
Buttons repeatedly to set the minute.
5.Press the or Buttons repeatedly to set the wake up mode to buzz
Press the or Buttons to set the volume level as desired.
7.Press the VOL +/AL 1 Button to save the settings and exit.
Alarm 2 setting:
Same as Alarm 1 settings above. But, press the VOL -/AL 2 Button instead of press the VOL
+/AL 1 Button.
IMPORTANT NOTE:
Alarm will not operate when the unit is power on mode.
If "F" (radio) was selected, select the desired radio station as previous procedure before
activating alarm.
SHUT OFF ALARM:
When alarm goes off, press POWER/FUNC Button to turn it off. The alarm will rest for next
day.
To turn off the alarm completely (not reset for next day).
SNOOZE
The alarm can be temporarily turned off manually by pressing the
SNOOZE/SLEEP/DIMMER Button; the alarm will turn back on automatically nine (9)
minutes later. This feature can be repeated until POWER/FUNC Button was pressed.
SLEEP
In the power on mode, press the SLEEP Button to activate the sleep function, SLEEP time
will appears on the display. Press the SLEEP Button repeatedly to set the sleep timer to
10-90 minutes as desired.
To turn off the unit before sleep timer time up, press and hold the POWER/FUNC Button
until “OFF” appear on the display.
DIMMER
When the unit is in standby mode. Press the SNOOZE/SLEEP/DIMMER to adjust the LED
display brightness level to high or low level.
Protect Your Furniture:
This model is equipped with non-skid rubber ‘feet’ to prevent the product from moving when
you operate the controls. These ‘feet’ are made from non-migrating rubber material
specially formulated to avoid leaving any marks or stains on your furniture. However certain
types of oil based furniture polishes, wood preservatives, or cleaning sprays may cause the
rubber ‘feet’ to soften, and leave marks or a rubber residue on the furniture. To prevent any
damage to your furniture we strongly recommend that you purchase small self-adhesive felt
pads, available at hardware stores and home improvement centers everywhere, and apply
these pads to the bottom of the rubber ‘feet’ before you place the product on fine wooden
furniture.
8
uninstalled in battery operating mode),
To read the current radio frequency or channel number in radio mode, press the CH MODE Button
repeatedly.
"b" (Buzz) or "F" (Radio) as desired.
6.Press the VOL +/AL 1 Button again, the volume level (two digits) of wake up sound will
appears on the display.
After press the POWER/FUNC
Button to turn off alarm, press the VOL +/AL 1 Button once, the AL 1 Indicator will turn off.
(For Alarm 2, press the VOL -/AL Button).
the button to auto search the next (previous) available station. (When a radio station was been
found, the frequency on display will stop running and start to playback the searched station.)
Press and release the or repeatedly to fine tune if needed.
(or batteries was consumed or
