background image

6

Notes:

• 

When the external BT player searched the unit, our model number “CHT756” will appear on the display of 

   external BT Device.

• 

Pairing code “0000” or “1234” may need to enter.

 

Normal operation after pairing: 

1. Turn on the BT function of the external BT Device. 
2. Press the Power ON/OFF Switch to ON position to power on the unit. The Blue Indicator will light, wait 

    until the Blue Indicator is stop blinking. (It needs take a few seconds). 

3. Plays the music in the paired BT Device as usual.

4. During playback:

• 

Turn the VOL (Volume) Control Knob to adjust volume level as desire. 

• 

Turn the BASS Control Knob to adjust bass (low audio frequency) level as desire.

5. When finished listening, press the Power ON/OFF Switch to OFF position to shut off the unit. The Blue 

   Indicator will not light.

NOTE: If long period of time will not use, unplug the AC/DC Adaptor from wall outlet. 

AUX IN:

To listen the music from external audio player suck like ipad; ipod; cell phone; MP3 player; Discman …:
1. Press the Power ON/OFF Switch to ON position to power on the unit. The Blue Indictor will light.
2. Connected one end of the supplied Audio Connection Cable to the 3.5mm stereo to the Phones Jack; Aux 
    out Jack or Line Jack on the external player.

3. Connect the other end to the AUX IN Jack on the unit. The unit will turn to AUX IN mode automatically. The 
    color of Blue Indicator will turns to Red.

4. Plays the Music in the connected audio player as usual. (Make sure the output level of the connected audio 

    player is set to high. Otherwise, sound from this unit is weak.)

5. Turn the VOL (Volume) Control Knob to adjust volume level as desire. 
6. Turn the BASS Control Knob to adjust bass (low audio frequency) level as desire.
7. When finished listening, unplug the Audio Connection Cable from the unit then press the Power ON/OFF 

    Switch to OFF position to shut off the unit. The Blue Indicator will not light.  

IMPORTANT: Make sure the Audio Connection Cable is unplugging from the unit before use BT. 

Otherwise, BT will not functioning.

General Specifications

Power Source:   

 

DC       12V, 1A,    

Audio Power: 

 

Left: 2.5W

   Right: 

2.5W

   Woofer: 

5.0W

Impedance of speakers:   

Subwoofer: 8 OHM; 15 W x 1

               

 

Left and Right speaker: 4 OHM; 5W x 2

Accessories:

1x User’s Manual
1x AC/DC Adaptor    

Input: AC 100-240V~,50/60Hz, 0.4A;

 

 

 

Output: DC       12V, 1A,    

1x Audio Connection Cable with 3.5mm Stereo Plugs

SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE

Summary of Contents for CHT756









Reviews: