Craftsman Speed Start 316.79401 Series Operator'S Manual Download Page 3

READ ALL INSTRUCTIONS BEFORE OPERATING

Read the instructions carefully. Be familiar with the controls and
proper use of the unit.

Do not operate this unit when tired, ill or under the influence of
alcohol, drugs or medication.

Children must not operate the unit. Teens must be accompanied
and guided by an adult. 

Inspect the unit before use. Replace damaged parts. Check for
fuel leaks. Make sure all fasteners are in place and secure.
Replace parts that are cracked, chipped, or damaged in any way.

All guards and safety attachments must be installed properly
before operating the unit. 

Be aware of risk of injury to the head, hands and feet.

Carefully inspect the area before starting the unit. Remove all
debris that can be thrown or become entangled with the unit,
such as rocks, glass, nails, wire, string, etc. 

Clear the area of children, bystanders and pets; keep them
outside a 50-foot (15 m) radius, at a minimum. Even then, they are
still at risk from thrown objects. Encourage bystanders to wear
eye protection. If you are approached, stop the unit immediately.

Squeeze the throttle control and check that it returns
automatically to the idle position. Make all adjustments or
repairs before using the unit.

WHILE OPERATING

Wear safety glasses or goggles that meet current ANSI Z87.1
standards and are marked as such. Wear ear/hearing protection
when operating this unit. Wear a face or dust mask if the
operation is dusty.

Wear heavy long pants, boots, gloves and a long sleeve shirt. Do
not wear loose clothing, jewelry, short pants, sandals or go
barefoot. Secure hair above shoulder level.

Use the unit only in daylight or good artificial light.

Avoid accidental starting. Be in the starting position whenever
pulling the starter rope. The operator and unit must be in a stable
position while starting. Refer to 

Starting and Stopping

.

Use the right tool. Only use this tool for its intended purpose.

Always hold the unit with both hands when operating. Keep a
firm grip on both handles or grips.

Keep hands, face, and feet away from all moving parts. Do not
touch or try to stop any moving parts while they are in motion.

Do not touch the engine, gear housing or muffler. These parts get
extremely hot from operation, even after the unit is turned off.

Do not operate the unit faster than the speed needed to do the job.
Do not run the unit at high speed when not in use.

Always stop the unit when operation is delayed or when walking
from one location to another.

Do not force the unit. It will do a better, safer job when used at
the intended rate.

Do not overreach or use the unit from unstable surfaces such as
ladders, trees, steep slopes, rooftops, etc. Always keep proper
footing and balance.

If you strike or become entangled with a foreign object, stop the
engine immediately and check for damage. Do not operate
before repairing damage. Do not operate the unit with loose or
damaged parts.

Turn the engine to off and disconnect the spark plug for
maintenance or repair.

Use only original equipment manufacturer (OEM) replacement
parts and accessories for this unit, as listed in the 

Parts List

section of this manual. Use of any other parts or accessories
could lead to serious injury to the user, or damage to the unit,
and void the warranty.

Keep the unit clean of vegetation and other materials that may
clog, gum or bind moving parts.

To reduce fire hazard, replace a faulty muffler and spark arrestor.
Keep the engine and muffler free from grass, leaves, excessive
grease or carbon build up.

• IMPORTANT SAFETY INSTRUCTIONS •

WARNING:

When using the unit, all safety rules must be

followed. Please read these instructions before operating
the unit in order to ensure the safety of the operator and any
bystanders. Please keep these instructions for later use.

3

BLOWER SAFETY

Do not insert anything into the air openings, blower tubes or
nozzle. Do not operate the unit if any of the air openings or
tubes are blocked. Keep the air openings free from dust, lint,
hair and anything else that may reduce airflow.

Do not operate the unit without the blower tubes attached.

Do not use the unit to spray liquids, especially flammable or
combustible liquids, such as gasoline. Do not use the unit in
areas where such liquids are present.

Do not use the unit for spreading chemicals, fertilizer or any
other substance that may contain toxic materials.

Do not set the unit down on any surface while the unit is
running. Debris can be picked up by the air intake and thrown
out the discharge opening, resulting in damage to the unit or
property or causing serious injury to bystanders or the operator.

During operation, never point the unit in the direction of people,
animals, windows or automobiles. Always direct blowing debris
away from people, animals, windows or automobiles.

Use extra caution when blowing debris near solid objects, such
trees, walls, fences, etc. When possible, blow away from such
objects, not toward them. 

Take care when working near valuable plants. The force of the
blown air could damage tender plants.

SAFETY WARNINGS FOR GAS UNITS

Store fuel only in containers specifically designed and approved
for the storage of such materials.

Always stop the engine and allow it to cool before filling the
tank. Never remove the fuel tank cap or add fuel when the
engine is hot. Always loosen the fuel tank cap slowly to relieve
any pressure in the tank before fueling.

Always add fuel in a clean, well-ventilated outdoor area where
there are no sparks or flames. DO NOT smoke.

Never operate the unit without the fuel cap securely in place.

Avoid creating a source of ignition for spilled fuel. Wipe up any
spilled fuel from the unit immediately, before starting the unit.
Move the unit at least 30 ft. (9.1 m) from the fueling source and
site before starting the engine. DO NOT smoke.

Never start or run the unit inside a closed room or building.
Breathing exhaust fumes can kill. Operate this unit only in a well
ventilated outdoor area.

WARNING:

Gasoline is highly flammable and its vapors

can explode if ignited. Take the following precautions:

Summary of Contents for Speed Start 316.79401 Series

















































Reviews: