background image

3

SAFETY INSTRUCTIONS

This symbol points out important safety instructions 

which, if not followed, could endanger the personal 

safety and/or property of yourself and others. Read and 

follow all instructions in this manual before attempting 

to operate this string trimmer. Failure to comply with 

these instructions may result in personal injury. When 

you see this symbol, HEED ITS WARNING!

   WARNING

!

This string trimmer was built to be operated according to 

the safe operation practices in this manual. As with any 

type of power equipment, carelessness or error on the 

part of the operator can result in serious injury. This ma-

chine is capable of amputating fingers, hands, toes and 

feet and throwing debris. Failure to observe the following 

safety instructions could result in serious injury or death.

  DANGER

!

CALIFORNIA PROPOSITION 65

Engine Exhaust, some of its constituents, and certain 

vehicle components contain or emit chemicals known to 

State of California to cause cancer and birth defects or 

other reproductive harm.

   WARNING

!

Your Responsibility—Restrict the use of this power machine 

to persons who read, understand and follow the warnings 

and instructions in this manual and on the string trimmer.

SAVE THESE INSTRUCTIONS!

   WARNING

!

GENERAL OPERATION

a.  Read this operator’s manual carefully in its entirety before 

attempting to assemble this string trimmer. Read, understand, 
and follow all instructions on the string trimmer and in the 
manuals before operation. Keep this manual in a safe place for 
future and regular reference and for ordering replacement parts.

b.  Be completely familiar with the controls and the proper use of 

this string trimmer before operating it.

c.  This string trimmer is a precision piece of power equipment, not 

a plaything. Therefore, exercise extreme caution at all times. 
This string trimmer has been designed to perform one job: to 
mow grass. Do not use it for any other purpose.

d.  Never allow children under 14 years of age to operate this string 

trimmer. Children 14 and over should read and understand the 
instructions and safe operation practices in this manual and on 
the string trimmer and should be trained and supervised by an 
adult.

e.  Only responsible individuals who are familiar with these rules of 

safe operation should be allowed to use this string trimmer.

f.  Thoroughly inspect the area where the equipment is to be used. 

Remove all stones, sticks, wire, bones, toys and other foreign 
objects, which could be tripped over or picked up and thrown 
by the trimmer line. Thrown objects can cause serious personal 
injury.

g.  Plan your trimming operation to avoid discharge of material 

toward roads, sidewalks, bystanders and the like. Also, avoid 
discharging material against a wall or obstruction, which may 
cause discharged material to ricochet back toward the operator.

h.  To help avoid trimmer line contact or a thrown object injury, stay 

in operator zone behind handles and keep children, bystanders, 
helpers and pets at least 75 feet from trimmer while it is in 
operation. Stop the string trimmer if anyone enters area.

i.  Always wear safety glasses or safety goggles during operation 

and while performing an adjustment or repair to protect your 
eyes. Thrown objects which ricochet can cause serious injury to 
the eyes.

j.  Wear sturdy, rough-soled work shoes and close-fitting slacks and 

shirts. Shirts and pants that cover the arms and legs and steel-
toed shoes are recommended. Never operate this string trimmer 
in bare feet, sandals, slippery or light-weight (e.g. canvas) shoes.

k.  Do not put hands or feet near rotating parts or under the cutting 

deck. Contact with cutting line can amputate fingers, hands, 

toes and feet.

l.  A missing or damaged discharge cover can cause cutting line 

contact or thrown object injuries.

m.  Many injuries occur as a result of the trimmer being pulled 

over the foot during a fall caused by slipping or tripping. Do 
not hold on to the trimmer if you are falling: release the handle 
immediately.

n.  Never pull the trimmer back toward you while you are walking. 

If you must back the trimmer away from a wall or obstruction, 

first look down and behind to avoid tripping and then follow 

these steps:

       1.  Step back from trimmer to fully extend your arms forward.
       2. Be sure you are well balanced with sure footing.
       3.  Pull the trimmer back slowly, no more than half way toward 

you.

       4. Repeat these steps as needed.

o.  Do not operate the trimmer while under the influence of alcohol 

or drugs.

p.   The safety control bar is a safety device. Never at

tempt to bypass 

its 

operation. Doing so makes the safety device inoperative 

and may result in personal injury through contact with the 
cutting line. The safety control bar must operate easily in both 
directions and automatically return to the disengaged position 
when released.

q.  Never operate the trimmer in wet grass. Always be sure of your 

footing. A slip and fall can cause serious personal injury. If you 
feel you are losing your footing, release the safety control bar 
immediately and the cutting line will stop rotating within three 
seconds.

r. Operate only in daylight or good artificial light. Walk, never run.

s.  Release the safety control bar when crossing gravel drives, walks 

or roads.

Summary of Contents for CMXGCAQ108493

































Reviews: