Craftsman CMXGAAM1085128 Instruction Manual Download Page 9

9

SERVICE AND MAINTENANCE

 WARNING

Before performing any type of maintenance/service, disengage all controls 
and stop the engine. Wait until all moving parts have come to a complete 
stop. Disconnect spark plug wire and ground it against the engine to 
prevent unintended starting. Always wear safety glasses during operation 
or while performing any adjustments or repairs.

Follow the maintenance schedule given below. This chart describes service guidelines 
only. Use the Service Log column to keep track of completed maintenance tasks. 

To 

locate the nearest authorized Service Center or to schedule service, call 
the following toll free number: 1-888-331-4569.     

Interval

Item

Service

Service Log

Each use

1. 

Engine oil level.

2. 

Leaf Blower and exhaust area.

1. 

Check.

2. 

Clean.

1st 5 hours

1. 

Engine oil.

1. 

Change.

Every 5 hours

1. 

Engine oil.

2. 

Exhaust area.

1. 

Check.

2. 

Clean.

25 hours

1. 

Spark plug.

1. 

Check. (See engine manual)

Every season/50 hours

1. 

Engine oil.

1. 

Change.

Every season/100 hours

1. 

Spark plug.

1. 

Clean, replace, re-gap. (See engine 

manual)

Every season/Before storage

1. 

Wheels

1. 

Lubricate.

Maintenance

 WARNING

Before performing any maintenance or repairs always stop engine.

Engine

Refer to the Engine Operator’s Manual for all engine maintenance procedures and 
instructions.

NOTE: 

Maintenance, repair, or replacement of the emission control devices and 

systems which are being done at owner’s expense may be performed by any 
qualifiedengine repair establishment or individual.

MAINTENANCE SCHEDULE

Cleaning the Blower

Any fuel or oil spilled on the machine should be wiped off promptly. Do NOT allow 
debris to accumulate around the cooling fins of the engine, the fan intake area or on 
any other part of the machine.

 WARNING

If the engine has been recently run, the engine, muffler and surrounding 
metal surfaces will be hot and can cause burns to the skin.  Exercise caution 
to avoid burns.

Lubrication

 WARNING

Before lubricating, repairing, or inspecting always stop engine.

Wheels

Lubricate the rear and axles with spray lubricant once per season.

Summary of Contents for CMXGAAM1085128





















Reviews: