background image

4

Setup

Attaching the Wrist Strap

1.

While facing the front of the tool, insert the thin end of

the wrist strap through one of the holes in the lower 

right corner of the tool.

2.

Push the thin end of the wrist strap until it goes

through the other hole.

3.

Separate the two wires, which make up the thin end

of the wrist strap, to form a loop.

4.

Insert the thick end of the wrist strap all the way 

through the loop in the thin end, so the wrist strap is

securely fastened to the tool (Figure 

B

).

Charging the Battery

Fully charge the battery before initial use and whenever 

the tool has not been used for 6 months or longer.

1.

Locate the port cover on the side of the tool

(Figure 

A

 #4).

2.

Using your finger, gently pull the port cover down

(Figure 

E

 #1).

3.

Insert the small end of the USB Recharge Cable into

the port on the side of the tool, making sure to insert 

the flat side of the cable into the flat side of the port 

(Figure 

E

 #2).

4.

Insert the USB end of the cable into a USB port in a

computer or USB power outlet (Figure 

E

 #3).

5.

Wait approximately 2.5 hours for the battery to fully

charge and then disconnect the USB Recharge 

Cable.

When the tool is ON, the battery level appears in the 

display window (Figure 

D

 #1).

Operation

1.

Point the laser at the top of the tool (Figure A #1) 

toward the wall whose distance you need to measure

(Figure 

C

 #1).

2.

Click   (Figure 

A

 #3) to turn the tool on and

display a laser dot on the wall (Figure 

C

 #1).

3.

When the bottom of the tool is positioned at the 

correct distance from the wall, click   to take the

measurement (Figure 

C

 #2).

4.

View the measurement on the display window

(Figure 

D

 #2).

Changing the Unit of Measure

Once the current measurement is taken, you can change 

the unit of measure from decimal ft (6.21 ft) to fractional 

ft (6'02"9/16), fractional ft to meters (1.894 m), meters to 

inches (74 9/16 in), or inches to decimal ft.
To change the unit of measurement, press and hold 

until you see the measurement change (2-3 seconds).
NOTE: If you continue to hold   after the measurement 

changes, the tool will turn off.

Re-measuring

If you need to take a new measurement, click  . 

•  The previous measurement (Figure 

D

 #2) will be

cleared from the display window.

•  When you are ready to take the new measurement,

click  .

Turning Off the Tool

The tool can be turned off in either of these ways: 

•  After taking a measurement, press and hold   for 

5 seconds (until the display window clears).

•  If you do not use the tool for 45 seconds, it will

automatically turn off.

Summary of Contents for CMHT77637












Reviews: