English
10
1. To connect the quick connect hose adapter
15
to a
garden hose, thread the quick connect hose adapter
onto the end of the garden hose. Tighten the garden
hose by hand.
nOTE:
Avoid cross threading when installing the hose.
Cross threading will cause leaks.
nOTE:
Before connecting the garden hose to the
power cleaner, run water through the garden hose for
thirty seconds to clear any debris from the mouth of
the garden pressure hose.
2. To connect the quick connect hose adapter
15
to the
quick connect filter
7
on the power cleaner
2
, push
the quick connect hose adapter firmly onto the quick
connect filter.
nOTE:
Before use, gently tug on the garden hose to
ensure the connection is secured. Make sure the quick
connect hose adapter is flush with the quick connect
filter as shown in Figure F.
3. Always disconnect the garden hose after usage. To
disconnect, pull back the collar on the quick connect
hose adapter and remove from the quick connect filter.
To Attach the Suction Hose (Fig. F, G)
Use the suction hose to pull water from a bucket or other
fresh water source.
NOTICE:
Do not use to suction soap, chemicals, dirty
or corrosive liquids, such as window cleaner, plant food,
fertilizers or bleach. Do not use salt water.
1. To connect the quick connect hose adapter
13
on the
end of the suction hose to the quick connect filter
7
on the power cleaner
2
, push the quick connect hose
adapter firmly onto the quick connect filter.
nOTE:
Before use, gently tug on the garden hose to
ensure the connection is secured. Make sure the quick
connect hose adapter on the end of the suction hose
is flush with the quick connect filter as shown in the
Figure F inset.
2. Place other end of suction hose with filter on it into
container of fresh water or a fresh water source. Adjust
the float ball
14
on the suction hose so the filter
20
stays covered in the liquid.
3. Select the correct nozzle to be used.
nOTE:
Turn the
nozzle to low pressure setting for watering. See
How to
Use the Multi‑Spray Nozzle
paragraph.
4. After the job being performed is complete, place the
suction hose into container of clean water and draw the
clean water through the system to rinse.
Attachments (Fig. E)
• Insert the end of the attachment into the opening on
the power cleaner
2
. Push in and turn the attachment
clockwise until its secured into working position.
• To remove the attachment, push in and turn the
attachment counterclockwise and pull from the power
cleaner
2
.
nOTE:
Other accessories are available for use with this power
cleaner, refer to the
Accessories
section.
Attaching Quick Connect Filter (Fig. D)
This power cleaner must be used with the quick connect
adapters. The garden or suction hose can only be attached
when the quick connect filter
7
is installed.
1. To connect the quick connect filter
7
to the power
cleaner
2
, place the end of the quick connect filter onto
the water intake
3
. Tighten the quick connect filter
by hand.
nOTE:
Avoid cross threading when installing the hose.
Cross threading will cause leaks.
SPECIFICATIONS
Maximum Pounds per Square Inch
350
Rated Gallons per Minute
0.5
Battery
20V DC
Inlet Hose
20 ft (6 m)
Pressure of Inlet Water
0‑80 PSI
Inlet Water
Cold Tap
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories.
An
accidental start‑up can cause injury.
VersaTrack™
WARNING:
Do not charge batteries while charger is
hung on Trackwall.
CRAFTSMAN chargers can be stored on CRAFTSMAN
VersaTrack™ Trackwall. Hooks and accessories are sold
separately. Please refer to the VersaTrack™ Trackwall accessory
sheet for further information.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
To Attach the Garden or Suction Hose
(Fig. F, G)
Connecting the garden hose or suction hose will depend on
the job to be performed.
To Attach Garden Hose (Fig. F)
This power cleaner must be used with the quick
connect adapters.
To Attach Nozzle to Spray Wand (Fig. H)
DANGER:
Risk of fluid injection. Do not direct
discharge stream toward persons, unprotected skin,
eyes or any pets or animals. Serious injury will occur.
WARNING:
Flying objects could cause risk of serious
injury. DO NOT attempt to change nozzles while power
cleaner is running. Turn power cleaner off before
changing nozzles.
To connect the nozzle to the spray wand
8
, pull the quick
connect collar
9
toward the spray wand and insert the
