Craftsman C950-60106-0 Setup Manual Download Page 4

Not 

for  

Reproduction

4

Note:  

The roll (transmission) release levers (a) may 

come from the factory in the RELEASE position. 

The tractor will not drive if leavers are in the release 

position.

Check - 

ROLL RELEAS S

Removing Tractor from Shipping 
Pallet

See Operator's Manual for starting, stopping, and 

operating information before driving tractor o

  shipping 

pallet.

Important: 

When driving tractor o

  shipping pallet 

raise the mower deck height to its highest cutting 

position.

a

a

Adjustment

The ground speed levers must be adjusted prior to use. 

Refer to the "Ground Speed Lever Adjustment" section 

in the Operator's 

DO NOT use roll release unless engine is OFF.

WARNING

Charge Battery

•  ALWAYS wear safety glasses for your protection 

while handling the battery. 

•  To avoid an explosion, keep 

fl

 ames and sparks 

away from the battery, especially while charging.

•  Battery acid causes severe burns. Avoid contact 

with skin.

•  Battery posts, terminals, and related accessories 

contain lead and lead compounds - chemicals 

known to the State of California to cause cancer 

and reproductive harm. Wash hands after handling. 

Note:  

If the unit is being put into service after the 

month and year indicated on the battery date tag 

(located on top of battery) charge the battery before 

use.

Note: 

Charge battery according to the instructions 

provided by the charger manufacturer.

Note: 

Read and understand any warnings by the 

battery manufacturer.

WARNING

RISK OF BATTERY EXPLOSION FROM HYDROGEN 

GAS MAY RESULT IN SERIOUS INJURY OR DEATH.

Summary of Contents for C950-60106-0













Reviews: