background image

15- ENG

D24456

MAINTENANCE

Customer Responsibilities

Daily or
after
each
use

Before
each
use

Yearly

(1)

1- more frequent in dusty or humid conditions

Check Safety Valve

Drain Tank

Air Filter

To ensure efficient operation and
longer life of the air compressor unit,
a routine maintenance schedule
should be prepared and followed.
The following routine maintenance
schedule is geared to an unit in a
normal working environment
operating on a daily basis. If
necessary, the schedule should be
modified to suit the conditions under
which your compressor is used. The
modifications will depend upon the
hours of operation and the working
environment. Compressor units in an
extremely dirty and/or hostile
environment will require a greater
frequency of all maintenance checks.

Unit cycles
automatically when

power is on. When performing
maintenance, you may be exposed
to voltage sources, compressed
air, or moving parts. Personal
injuries can occur. Before
performing any maintenance or
repair, disconnect power source
from the compressor and bleed off
all air pressure.

To Check Safety Valve

If the safety valve
does not work

properly, over-pressurization may
occur, causing air tank rupture or
an explosion. 

1.

Before starting compressor, pull
the ring on the safety valve to
make sure that the safety valve
operates freely. If the valve is
stuck or does not operate
smoothly, it must be replaced
with the same type of  valve. 

Air compressor pump intake
and exhaust valves

To Drain Tank

1.

Set the On/Auto/Off lever to
"OFF".

2.

Pull the regulator knob out and
turn counterclockwise to set the
outlet pressure to zero.

3.

Remove the air tool or
accessory.

4.

Pull ring on safety valve allowing
air to bleed from the tank until
tank pressure is approximately
20 psi. Release safety valve ring.

5.

Drain water from air tank by
opening drain valve (counter-
clockwise) on bottom of tank.

Water will
condense in the air

tank. If not drained, water will
corrode and weaken the air tank
causing a risk of air tank rupture.

Frequently

Summary of Contents for 919.72458













































Reviews: