background image

23

The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your
CORDLESS TRIM SAW or when ordering repair parts.

SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS

CRAFTSMAN 18 VOLTS PROFESSIONAL CORDLESS TRIM SAW – MODEL NUMBER 315.271190

PARTS LIST

Key

Part

No.

Number

Description

Quan.

Key

Part

No.

Number

Description

Quan.

1

982174-001

Data Plate ................................................... 1

2

** Item No. 

9

-11034

Battery Pack (981404-001) ......................... 1

3

982158-001

Upper Blade Guard ..................................... 1

4

982159-001

Upper Blade Guard Screw .......................... 4

5

** Item No. 

9

-11040

Charger (981399-001) ................................ 1

6

982160-001

Spring .......................................................... 1

7

982161-001

Lower Blade Guard ..................................... 1

8

982162-001

Guard Retainer ........................................... 1

9

982163-001

Guard Retainer Screw ................................ 4

10

6112003                  Inner Blade Washer .................................... 1

11

982427-001

Lower Blade Guard Handle ........................ 1

12

982428-001

Screw .......................................................... 1

13

       *

Saw Blade ................................................... 1

14

975533-000

Outer Blade Washer ................................... 1

15

975532-000

Blade Screw ................................................ 1

16

982426-001

Bumper Screw............................................. 1

17

982425-001

Bumper ........................................................ 1

18

975544-000

Lock Nut ...................................................... 2

19

982164-001

Spring .......................................................... 1

20

982165-001

Spindle Lock ................................................ 1

21

982166-001

Knob ............................................................ 2

22

982167-001

Washer ........................................................ 2

23

982168-001

Carriage Bolt (M6 x 12 mm) ........................ 1

24

975558-000

Screw .......................................................... 1

25

975559-000

Hex Nut ....................................................... 1

26

982169-001

Wing Screw ................................................. 1

27

982170-001

Washer ........................................................ 1

28

975552-000

Spring .......................................................... 1

29

982171-001

Base Screw ................................................. 1

30

982172-001

Base Assembly ........................................... 1

31

982173-001

Carriage Bolt (M6 x 100 mm) ...................... 1

32

975553-000

Blade Wrench (5 mm Hex Key) .................. 1

33

975554-000

Rip Guide .................................................... 1

34

982175-001

Carrying Case – Not Shown

972000-765

Owner’s Manual

 * Available At Your Nearest Sears Catalog Order Or Retail Store

** Can Be Purchased Thru RSOS (Retail Special Order System)

Summary of Contents for 315.271190

























Reviews: