background image

OPERATING INSTRUCTIONS

ATTACHING DRIVE BOARDS AND PADS

•  Tilt the machine back on its wheels until the back of the motor housing is resting on 

the floor exposing the drive mechanism at the front.

•  A drive board or the brush should now be placed on the drive mechanism and locked 

in place by turning anti-clockwise.

•  When using the machine with the drive board select the correct size and grade of pad 

and fit to the drive board.

•  With the drive board or brush fitted the machine can be returned to the upright po-

sition.

•  Reverse the process to remove the drive board or the brush.

OPERATING THE MACHINE

•  Plug into power supply and check that green indicator light is on.

•  The handle should be adjusted to a comfortable working height when the pad or 

brush is flat on the floor.

•  The handle is adjusted by pulling the height adjustment lever – this allows the handle 

to be adjusted

•  The handle will lock into position when this lever is released.

•  Lift the handle so that the machine base is parallel to the floor.

•  Operate the machine by sliding one of the safety switches outwards and lifting one of 

the on/off levers as above.

•  The temperature of the drive board is regulated by the thermostat dial.

•  This primarily should be set at 85°C for use with the aluminum drive board and 0°C for 

use with the carpet shampoo brush and plastic type drive board.

•  To set the heatgun temperature, adjust the red knob located on the top of the heat 

gun and set between 5 and 6 on the dial.

•  When the machine is tilted back – with the back of the motor housing resting on the 

floor and the aluminum drive board in place – attach a wet carpet pad onto the board 

and use as per previous instructions.

•  Caution: the aluminum drive board gets extremely hot – when handling use heat resis-

tant gloves to avoid burns etc.

•  To adjust the pressure on the drive board or the carpet shampoo brush the weight can 

be added by placing in position and hand tightening the bolts provided.

CONTROLLING MACHINE MOVEMENT

•  When the brush or pad is flat on the floor – the machine will stay in the

•  central position.

•  To move to the right – slightly raise the handle and the machine will move to the right.

•  To move to the left – slightly lower the handle and the machine will move to the left.

•  The speed at which the machine moves either left or right will depend entirely on the 

amount the handle is raised or lowered.

ROUTINE MAINTENANCE:

•  Always remove plug from socket outlet before carrying out any routine maintenance.

•  Wipe all surfaces of machine after use.

•  Always wind the cable around the bottom cable hook and handle.

•  Wipe power cable clean after use – using a damp cloth.

•  Check cable visually for signs of wear and damage - if any is detected, ensure that it 

is replace immediately – this operation need not require a service call as a new cable 

(see safety information) can be plugged in by unqualified personnel.

Summary of Contents for thermadry







Reviews: