Craftex CT052 Manual Download Page 6 | Manualshive

Page: 6 / 20

Craftex CT052 Manual Download Page 6

6

UNPACKING

Carefully remove the items packed in the
carton. It may be a good idea to save the
carton and packing material in case it might
be needed in the future. Upon removal of all
items from the package, you should have:

1.

Dovetail Jig

2.

Hand Levers (2)

3.

Manual

Figure 1 shows the dovetail jig with handles

ASSEMBLY

A. HAND LEVERS

The jig is shipped fully assembled except for
the two hand levers. Screw the threaded end
of each hand lever into the clamping rods
located on the top

,

and front of the dovetai

l.

Tighten until secure. Figure-1

B. MOUNTING

Place the jig on your bench top so the front
lap rests against the front of the bench top.

Locate the mounting holes in the rear of the
jig. Mark the holes locations with a pen and
determine whether to use nuts and bolts or
lag screws. Drill the appropriate size holes

.

Secure the jig to your bench top. Screw can
be tighten by inserting a long screw driver
through the unthreaded holes in the back of
the jig.

Hint:

If you do not wish to permanently

devote bench space to  the dovetail jig,
mount the jig to a piece of 3/4"  plywood
that can be clamped to  your bench top or
clamp the jig to the front of your bench

«
...
4
5
6
7
8
...
»

Summary of Contents for CT052





















Reviews:

No comments