CR Remeha Quinta Pro 115 Installation And Service Manual Download Page 30

Page: 30 / 92

4.8.3.

Standard control PCB

Various thermostats and controllers can be connected to the standard

control PCB (PCU) (

X12

connector block).

Access to the connector block:

1. Unscrew the two screws located under the front panel by a quarter

turn and remove the panel.

2. Guide the cables from the controller or thermostat through the

round grommet(s) on the right in the boiler bottom plate.

3. Tilt the control box forwards by opening the holding clips located

at the sides.

4. Open the tooling box by opening the clip fastener on the front side.
5. Run the connection cable(s) through the grommet(s) in the control

unit box.

6. Unscrew the necessary cable clamps (to access the connector

block) and introduce the cables.

7. Connect the cables to the appropriate terminals on the connector

block.

8. Firmly retighten the cable clamps and close the control panel.

4.8.4.

Connecting the pump

The pump must be connected to standard control PCB (PCU). To do

this, proceed as follows:
1. Connect the cable, that is delivered with the boiler, to the pump.

R000075-B

/off

Tou

X13

X12

90º

T002047-B

X81

4. Installation

Quinta Pro 30 - 45 - 65 - 90 - 115

250413 - 123157-03

Summary of Contents for Quinta Pro 115





























































































Search results

Summary of Contents for Quinta Pro 115

Reviews:

Related manuals for Quinta Pro 115

Brands by name

Popular brands

CR Remeha Quinta Pro 115, Installation And Service Manual

Search results

Summary of Contents for Quinta Pro 115

Reviews:

Related manuals for Quinta Pro 115

Brands by name

Popular brands