background image

 

 

 

13

 

turned off before any connection is made or removed.

 

The system has a thermal element that will shut off the flow of gas in the event of a fire. 

The system has a flow limiting device which, when activated, will limit the flow of gas to 10 cubic feet per 

hour. 

NEVER

 use side burner without leak testing this connection. 

LP (Propane) Gas Supply Connection 

1.

 

The  tank  valve  should  be  in  the  “OFF”  position.  If  not,  turn  the  knob 

clockwise until it stops.   

2.

 

Make sure all burner valves are in the “OFF” position.   

3.

 

Always connect the gas supply regulator as follows:   

Insert  the  regulator  inlet  into  the  tank  valve  and  turn  the  coupling  nut 

clockwise until the coupler tightens up (see picture). Do not over-tighten the 

coupler. Turn the main tank valve on, and turn the burner control valves on 

the unit to the “HIGH” position for about 20 seconds to allow the air in the 

system to purge before attempting to light the burners.   

Pre-Operation Leak Testing 

 

1.

 

Do not insert any tool into the valve outlet or safety relief valve. You may damage the valve and cause a 

leak. Leaking propane may result in explosion, fire, severe personal injury, or death.   

2.

 

If a leak is detected at any time, or you cannot stop a gas leak, immediately close the tank’s shut-off valve 

(gas supply from LP tank to the Side burner) and call LP gas supplier or your fire department!   

3.

 

Check all gas supply fittings before each use and each time the gas supply cylinder is connected to the 

regulator. Have a qualified service technician leak test the side burner any time a part of the gas system is 

replaced. 

 

Never attempt to attach this side burner to the self-contained LP gas system. Do not use the side burner until 

leak testing has been completed. 

 

Leak Testing Valves, Hose and Regulator

 

1.    NEVER smoke while leak testing. 

2.  Extinguish  all  open  flames.  Never  leak  test  with  an 

open flame.   

3.  Mix a solution of equal parts mild detergent or liquid 

soap and water.   

4.  Turn all side burner control knobs to OFF. 

5.  Ensure that the connections from the regulator to the 

side  burner  and  tank  are  tight  and  secure  (see 

picture).   

Summary of Contents for C1PB





























Reviews: