COX A16413K Cruiser, Owner'S Operation Manual, Page: 6 / 58

24 October 2014 Page 6 Cruiser Model A16413K rev 1
OPERATING INSTRUCTIONS
IMPORTANT
The careless or improper use of a machine of this type can be
dangerous. The manufacturer or selling agent does not accept
responsibility for accident either to the operator, to the owner or
to any person directly or indirectly or to property if such accident
is caused by circumstances arising other than by the negligence
or default of COX INDUSTRIES.
RECOMMENDED FUEL
Unleaded fuel is recommended by all manufacturers of
engines fitted to Cox products (up to 10% ethanol blended
unleaded fuel is acceptable).
SAFETY SWITCHES
Before operating machine, ensure that all safety switches are
operating correctly as per Pre-delivery Instructions. Do not
operate machine with faulty, missing or damaged safety
switches.
BLADE WARNING
Do not use mowing attachment with broken, bent, or
damaged blades, or damaged or worn bolts and nuts
otherwise damage and premature wear will result from
vibration. Recommended Cutter Blade Bolt and Nut torque
is 36-40Nm. Do not over tighten.
Keep feet and hands clear of the mowing attachment
at all times while operating or attempting to start the
machine.
WARNING
DO NOT OPERATE THE MOWING ATTACHMENT
WITHOUT DISCHARGE DEFLECTOR FITTED & DOWN
.
Reference to left or right hand side of machine is determined
by sitting in the operating position on the machine.
Safety footwear is recommended when operating machine.
Mount and dismount only from the centre front or non
discharge side of machine.
Ensure machine has Clutch/Park Brake Lever set in the ON
position and Drive Levers are in the locked out NEUTRAL
position and Cutter PTO Switch is in the DISENGAGED
position while attempting to start engine.
Never allow engine revs to exceed 3600 RPM.
TO OPERATE
BEFORE STARTING/SWITCHING OFF:
Read & Follow Engine Owners Manual Instructions.
Before stopping the engine:
Stop the mowing attachment
Return the engine speed control to slow position .
Then turn the Key Switch to the OFF position.
STARTING ENGINE
When starting machine, place Drive Levers in the locked out
NEUTRAL position. Ensure that Cutter PTO Switch is in the
DISENGAGED position and the Clutch/Park Brake Lever is set
in the ON position otherwise electric start will not be
activated. If engine is cold, pull choke control (if equipped)
up to choke position and engine speed control knob to fast
position, or move engine speed control knob to choke
position. Turn key switch to start position and release to the
on position once engine has started. Once engine is running
gradually return the choke control (if equipped) to depressed
position, or move engine speed control to the fast position.
Do not continue to operate the engine in the choke position.
If engine is hot move engine speed control to the fast
position. Turn key switch to start position and release to the
on position once engine has started.
TO OPERATE THE MOWING ATTACHMENT:
Bring the engine up to the normal operating speed.
The Mowing Attachment is engaged by puling up the large
yellow knob (P.T.O. Switch) on the left hand control panel.
Before starting ensure knob is in the disengaged position
(down). For safety it is advisable that the mowing
attachment be not operating (Cutter PTO Switch be in the
disengaged position) other than when mowing grass.
TO DRIVE FORWARD/REVERSE:
Engine speed and ultimate drive speed is regulated by
setting the engine speed control to desired engine speed.
To drive forward push both the drive control levers forward
from the neutral position.
To drive in reverse pull both the drive control levers back
from the neutral position.
The further the drive control levers are moved from neutral
the faster the drive speed.
To slow down when driving forward pull both drive control
levers back.
To slow down when driving in reverse push both drive
control levers forward.
The position of the drive control levers can be used to
control the ground speed, especially in heavier conditions.
Owing to the inline action of the drive levers, it is possible to
take the machine straight from forward to reverse and vice
versa.
MANOEUVRING/TURNING:
The independent forward and reverse operation of 2
separate drives makes the machine very manoeuvrable and
the sharpest turns can be negotiated easily and quickly.
Move the left hand drive control lever forward to turn the
machine in a right hand turn direction.
Move the right hand drive control lever forward to turn the
machine in a left hand turn direction
Move the left hand drive control lever backwards to turn the
machine in a left hand turn direction.
Move the right hand drive control lever backwards to turn
the machine in a right hand turn direction.
Adjustment of the speed of each rear wheel to suit the
turning manoeuvre required will minimise the possible
damage to the turf caused by having one wheel rotating too
slow for the manoeuvre required.
TO BRAKE (WITH ENGINE RUNNING):
The drive levers should be used to stop the machine travel.
Do not use the park brake lever to stop the machine travel
except in an emergency as the park brake mechanism will be
permanently damaged.
If travelling forward pull both drive control levers backwards
evenly until the machine travel stops, then return both the
drive control levers to the neutral position.
If travelling in reverse push both control levers forward
evenly until the machine travel stops, then return both the
drive control levers to the neutral position.
CLUTCH/PARK AND TRANSPORTATION BRAKE:
The clutch/park brake lever is located on the front left hand
side of the control housing. Pull the lever up fully and to the
right then lower into the “L” slot to engage the brake. Pull
the lever up and to the left out of the “L” slot and then lower
completely to disengage clutch/park brake.
Do not attempt to bring the machine to a stop using
the Clutch/Park Brake Lever as permanent damage
will be done to the Park/Brake mechanism.
CUTTING HEIGHT ADJUSTMENT:
The cutter height adjustment lever is located on the front
right hand side of the control housing, and may be raised to
suit various conditions.
To raise the mowing attachment, lift the height adjustment
lever to the desired height. It is not necessary to depress
the button when lifting the mowing attachment.
To lower the mowing attachment, lift the height adjustment
lever slightly and depress button, once button is depressed
lower the mowing attachment to the desired position and
release button.
NOTE: When mowing on slopes, keep drive levers in
forward or reverse, depending on direction of travel.
The low gearing will prevent it from picking up
excessive speed. If very steep it may be necessary to
reduce engine speed slightly.