background image

27

O

thers

SPECIFICATION

Product name

 Bidet

Model name

BA07-R/E

Power rating

120 V~  60 Hz

Power consumption

850 W

Power cord

1.2 m (47 inch) long

Water pressure

0.075 MPa - 0.68 MPa

Product 

dimensions

BA07-R

490 mm (W) X 510 mm (D) X 150 mm (H)

BA07-E

490 mm (W) X 540 mm (D) X 150 mm (H)

Weight (NET)

5.7 kg

Warm water 

cleansing 

device

Rear cleansing

Maximum 0.7 L/min, automatic nozzle cleaning function

Front cleansing

Maximum 0.7 L/min, automatic nozzle cleaning function

Timing

Rear cleansing 1 min, Front cleansing 1 min

Water pressure control

Micom control, 3 level control

Wide (spray range control)

3 level spray range control(straight-level 1-level 2)

Warm water temperature adjustment

4 levels 

(off : tap water temperature, low : 34 ºC, medium : 36 ºC, high : 38 ºC)

Power consumption of cistern heater

800 W

Cistern capacity

0.8 L

Safety device

Bi-metal, temperature sensor, temperature fuse(overheating prevention)

Warm air dryer

Warm air temperature control

3 levels

Timing

Air dryer 2 min

Power consumption of dryer heater

210 W

Safety device

Bimetal, temperature fuse(overheating prevention)

Warm seat

Seat temperature control 

(after seating)

4 levels 

(off : room temperature, low : 34 ºC, medium : 37 ºC, high : 40 ºC)

Power consumption of dryer heater

50 W

Safety device

Temperature sensor, temperature fuse(overheating prevention)

MF filter

Life span

4 months (2.5 ton/month, impurity rate : under 0.5 NTU)

Dimension

(L) 136 mm × (Ø) 48 mm 

Accessories

Installation materials

T-Shaped connector, Rubber packing, Bidet hose, 2 Fixing washers, 

2 Fixing screws, 2 Fixing nuts, 2 Fixing rubbers, Fixing plate,

2 Fixing sliders, MF filter

Other function

Nozzle position adjustment, Move, Nozzle cleaning, Seat locking mode, 

Remote control auto power saving mode.

Temperature

0 ºC - 40 ºC

 

Manufactured by WOONGJIN CUCHEN CO., Ltd.

 

These specifications may be changed to improve the performance of the product.

 

Earlier clogging may occur in MF filter depending on quality and consumption of water.

TROUBLESHOO

TING / SPECIFIC

ATION

1014692 BA07 »ç¿ë¼³¸í¼- ¹ÌÁÖÇâ_(08.09.10).indd   27

2008-09-10   ¿ÀÀü 11:37:34

Summary of Contents for BA07-E

































Reviews: