manualshive.com logo in svg

Covidien Puritan Bennett 700 Series, Service Manual

Share
Download
Covidien Puritan Bennett 700 Series Service Manual Download Page 281

Service and repair

Puritan Bennett™ 700 Series Ventilator System Service Manual

10070389 Rev. A

8-23

Figure 8-18. Removing Communications option assembly

8.6.3.1  Remote alarm harness and connector 

(See Figure 8-19 and Figure 8-20). Remove the remote alarm harness as follows. Install by 
reversing removal procedure.

1.

Remove the Communications option assembly and disconnect the ribbon cable 
(Section 8.6.3).

2.

Disconnect the remote alarm harness from the J2 connector on the PCB assembly.

3.

Use a 19-mm open-end wrench to loosen the lock nut that holds the remote alarm 
connector to the option plate.

4.

Push the harness and connector through the plate to remove.

7-00011

Summary of Contents for Puritan Bennett 700 Series
























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands