manualshive.com logo in svg

Covidien Puritan Bennett 700 Series, Service Manual

Share
Download
Covidien Puritan Bennett 700 Series Service Manual Download Page 271

Service and repair

Puritan Bennett™ 700 Series Ventilator System Service Manual

10070389 Rev. A

8-13

Figure 8-9. Removing shelf mount from ventilator

8.4.2  Removing/installing collector vial support bracket

(See Figure 8-8). Using 3-mm hex driver, remove two M4 x 10 screws, flat washers, and split-
ring washers that retain support bracket to shelf mount plate. Remove support bracket. 
Install by reversing removal procedure.

8.4.3  Removing/installing humidifier support bracket

(See Figure 8-8). Remove two M5 x 10 flat-head screws (Fisher & Paykel™* bracket) or four 
M5 x 20 flat-head screws (Hudson RCI™* bracket) that retain support bracket to shelf mount 
plate. Remove bracket. Install by reversing removal procedure.

To unlock

Shelf

Ventilator

Shelf

Ventilator

7-00184

Interlocking 
rails locked 
in place

Interlocking 
rails clear 
slots on shelf

Summary of Contents for Puritan Bennett 700 Series
























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands