Safety • Specifications
2
Important Safety Instructions
SAVE THESE INSTRUCTIONS - This manual contains
important instructions that should be followed during
installation, operation, and maintenance of the product.
This is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for one of
the following signal words and be alert to the potential
for personal injury!
indicates a hazard which, if not avoided,
will
result in death or serious injury.
indicates a hazard which, if not avoided,
could
result in death or serious injury.
indicates a hazard which, if not avoided,
could
result in minor or moderate injury.
NOTICE
addresses practices not related to
personal injury.
Carefully read and follow all safety instructions in this
manual and on pump.
Keep safety labels in good condition. Replace missing or
damaged safety labels.
California Proposition 65 Warning
This product and related accessories contain
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
The manufacturer cannot anticipate every possible
circumstance that might involve a hazard. The warnings
in this manual, and the tags and decals affixed to the unit
are, therefore, not all-inclusive. If you use a procedure
or operating technique that the manufacturer does not
specifically recommend, you must satisfy yourself that it
is safe for you and others. You must also make sure that
the procedure or operating technique that you choose
does not render the system unsafe.
Electrically powered sewage pumps normally give many
years of trouble-free service when correctly installed,
maintained, and used. However, unusual circumstances
(interruption of power to the pump, large solids in
the sump, flooding that exceeds the pump’s capacity,
electrical or mechanical failure in the pump, etc.) may
prevent your pump from functioning normally. To prevent
possible damage, consult your dealer about installing
a secondary sewage pump or a high water alarm. See
Troubleshooting
in this manual for information about
common sewage pump problems and remedies. For more
information, see your retailer or call customer service.
Risk of electric shock.
Can shock, burn
or kill. During operation the pump is in water. Shock
can cause serious injury or death. Failure to follow the
warnings below can result in fatal electric shock.
• Check your local codes before installing. You
must comply with their rules. Only qualified
personnel should install the pump and associated
control equipment.
• Ground the pump according to all applicable codes.
• Take care when changing fuses or resetting the circuit
breaker. Disconnect power to the pump before
servicing. Do not stand in water when working on
the control box or with the circuit breaker panel.
• Do not modify cord and plug. When using cord and plug,
plug into a grounded outlet only. When wiring to a system
control, connect pump ground lead to system ground.
• Do not remove cord or strain relief. Do not lift the
pump by the power cord or hang the pump by the
power cord (See
Cord Lift Warning
).
Risk of burns.
Motors can operate at high
temperatures. To avoid burns when servicing the pump, allow
it to cool for 20 minutes after shut-down before handling it.
Risk of explosion and hazardous gas.
Septic system must be vented in accordance with local
plumbing codes.
• Do not smoke or use sparkable electrical devices or
flame in a septic (gaseous) or possible septic sump.
• If a septic sump condition exists and if entry into
sump is necessary, then (1) provide proper safety
precautions per OSHA requirements and (2) do
not enter sump until these precautions are strictly
adhered to.
• Do not install the pump in any location classified as
hazardous by National Electrical Code, ANSI/NFPA
70-1984.
Wear safety glasses at all times when working with
the pump.
Do not run the pump dry. Dry running can overheat the
pump and will void the warranty.
In normal service, motor should not need oiling. Motor
has been filled at the factory with a special oil.
NOTICE
This unit is not designed for applications
involving salt water or brine! Use with salt water or brine
will void warranty.
This pump is designed for use in a residential sewage or
septic system only. Not designed for use as a swimming
pool drainer. Do not use where water recirculates. Use
only within design parameters.
Pump water only with this pump.
Specifications
H.P.
Voltage
Individual Branch Circuit
Required (Amps)
Dual Element Time
Delay Fuse Amps
3/4
115
15
15
Performance
GPH (Liters) at discharge ft. of head (m)
5’ (1.5m)
10’ (3m)
15’ (4.6m)
20’ (6.1m)
Max Lift (No Flow)
11,400
(43,140)
9,180
(34,740)
6,300
(23,848)
2,400
(9,085)
22’ (6.7m)
Summary of Contents for CLW750-01
Page 12: ......