Cotic droplink Flare Gen2 Owner'S Manual Download Page 12

Warranty

 

 
The warranty terms for your Cotic frame are detailed on your invoice.
This applies regardless of any subsequent changes to the warranty terms.

 

 

 

 

 

 

 
 

Setup Suggestions

 

 
The suspension on your Cotic 

drop

link

 bike is designed to work at it’s best when the suspension ‘sags’ with the rider 

on board the bike. 'Sag' is the amount the shock compresses with a rider on board. The suspension works at its best 
when set with between 25% and 30% of the available travel as sag. 
 
You should be looking to set up your bike between the following amounts of sag, measured on the shaft of the shock: 
 
 
 
 
 
 
 
 
 
 

 

 

 

 

 

 

 

 

 

 

 

            drop

link

 Model                                   25% Sag                                        30% Sag

 

                Rocket Gen4                                           16mm                                                19mm 

             RocketMAX Gen3                                       16mm                                                19mm

 

                   Jeht Gen1                                             14mm                                                16mm 

    Flare Gen2 (45 stroke shock)                               11mm                                                14mm

 

    Flare Gen2 (50 stroke shock)                              12.5mm                                              15mm 

                   FlareMAX                                            12.5mm                                              15mm 

 

Summary of Contents for droplink Flare Gen2

















Reviews: