Costco 1902481 Assembly Manual Download Page 2

SAFETY INFORMATION

PREPARATION

Screwdriver

Safety goggles

Hammer

Gloves

Stepladder

Hardhat

Electric drill

Before beginning assembly of product, make sure all parts are present. Compare parts with 

package contents list and hardware contents list. If any part is missing or damaged, do not 

attempt to assemble the product. 

Estimated Assembly Time: 3 hours.

Tools Required for Assembly (not included in the box): 

For the best assembly and usage experience, please read through all steps before attempting to 

assemble, operate or install the product

WARNING

:

 

It is the consumer’s responsibility to comply with any building codes, ordinances,

zoning limitations, or local homeowner’s restrictions and obtain any required permit, before

purchase and installation of the products.

WARNING

: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS GAZEBO FABRIC.

This item meets the CPAI-84 flammability requirements. The fabric may burn if left in continuous

contact with any flame source. The application of any foreign substance to the tent fabric may

cause the flame-resistant properties ineffective.

• In the case of any high winds or high amounts of rain/snow, please remove the mosquito net,

clear the snow from the roof immediately and check for damage before continuing use.

CAUTION

SET UP YOUR GAZEBO PROPERLY 

• This product is heavy so do not attempt to assemble this item alone. For the best and safest

assembly experience, we recommend four (4) adults.

• Keep all children, pets and other obstructions away from assembly area.

• If any part is missing or damaged, do not attempt to assemble the product.

• In order to avoid damage to the gazebo and it's components, please use the appropriate tools.

• Do not use the structure as support.

• Check all bolts on a regular basis to maintain the sturdiness and safety of the structure.

• Keep instruction manual for future use.

• Do not climb on top of the gazebo. Falling off the gazebo can result in serious injury,

possibly even death.

EXAMINE YOUR GAZEBO

• Examine occasionally to ensure there are no loose parts.

• If loose parts are found, they should be retightened immediately.

-2-

Summary of Contents for 1902481

















Reviews: