Costar CRIS10 Operation Manual Download Page 16 | Manualshive

Page: 16 / 22

background image

16

Part 2 - Installation

Installation

1

Place the product in a even and safe place, and prepare for a regular headed screwdriver of
medium size (

0.6 cm/0.24 inch)..

2

Screw brackets to the two sides (3 points for each) of the front panel by using the provided
screws and the prepared regular headed screwdriver of medium size. See the first image
below.

3

Mount the product to the rack by screwing brackets to the rack by using screws provided
with the rack.

Braket to the product

Product to the rack

«
...
14
15
16
17
18
...
»

Summary of Contents for CRIS10























Reviews:

No comments

Related manuals for CRIS10

Brand: OFFICINE OROBICHE Pages: 7

Brand: 3Com Pages: 8

PathBuilder S200 Series

Brand: 3Com Pages: 11

Brand: 3Com Pages: 8

CoreBuilder 3500

Brand: 3Com Pages: 96

Brand: G&D Pages: 36

Brand: Lantronix Pages: 40

Brand: Lantronix Pages: 2

SISTP1040-551-LRT

Brand: Lantronix Pages: 2

Brand: Lantronix Pages: 2

SISPM1040-3 L Series

Brand: Lantronix Pages: 2

SISPM1040 L3 Series

Brand: Lantronix Pages: 36

SecureLinx Spider

Brand: Lantronix Pages: 18

Brand: Lantronix Pages: 8

Brand: Lantronix Pages: 6

SISPM1040-582-LRT

Brand: Lantronix Pages: 272

Xpress-Pro SW 52000

Brand: Lantronix Pages: 8

Brand: AVLT-Power Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands