Costar 4 Channel User Manual Download Page 83

Page: 83 / 83

4-Channel Digital Video Recorder

V1.3

Specifications

VIDEO

Signal Format

NTSC or PAL (Auto Detect)

Video Input

Composite: 4 looping inputs, 1 Vp-p, auto-terminating, 75 Ohms

Monitor Outputs

Composite: 1 BNC, 1 Vp-p, 75 Ohms
SPOT: 1 BNC, 1 Vp-p, 75 Ohms
VGA: 1

Video Resolution

Composite: 720x480 (NTSC), 720x576 (PAL)
VGA: 800x600, 1024x768, 1280x1024 @ 60Hz

Record/Playback Speed
(images per second)

120ips (NTSC), 100ips (PAL) @ Half D1 (Full Duplex)

INPUTS/OUTPUTS

Alarm Input

4 terminal, programmable as NC or NO, 1.1V threshold, 5VDC

Alarm Output

1 relay output, programmable as NC or NO, 2A@125VAC, 1A@30VDC

Alarm Reset Input

1 TTL, terminal block

Internal Buzzer

80dB at 10cm

Network Connectivity

10/100 Mbps Ethernet (RJ-45)

Audio Input

RCA Input: 4 Line In

Audio Output

RCA Output: 1, Line Out

Text Input

POS Interface, ATM Interface

CONNECTORS

Video Input

Composite: 4 BNC

Video Loop

Composite: 4 BNC (Auto Terminating)

Monitor Output

Composite: 1 BNC
SPOT (Composite): 1 BNC
VGA: 1 VGA

Audio In

4 RCA connector

Audio Out

1 RCA connector

Alarm Input/Output

Terminal Blocks

Ethernet Port

RJ-45

RS232C Serial Port

DB9 (P)

RS485 Serial Port

Two-connector terminal block

IR Port

1 Remote Control

USB Port

2 (USB 2.0)

STORAGE

Primary Storage

SATA hard disk drive (up to 4) (up to 3 with an internal DVD RW drive)

Secondary Storage*

Built-in DVD RW drive
USB hard disk drive or flash drive

GENERAL

Dimensions (W x H x D)

16.9

x 3.5

x 15.9

(430mm x 88mm x 405mm)

Unit Weight

14.8 lbs. (6.7kg)

Shipping Weight

22.0 lbs. (10.0kg)

Shipping Dimensions
(W x H x D)

21.3

11.4

x 23.2

" (

540mm x 290mm x 590mm)

Operating Temperature

41°F to 104°F (5°C to 40°C)

Operating Humidity

0% to 90%

Power

100 to 240 VAC, 1.2 – 0.6 A, 60/50Hz

Power Consumption

Max. 45W

Approvals

FCC, UL**, CB, CE

When installing an internal DVD RW drive, connect the SATA I/O cable to the SLAVE2(ODD) socket.

CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the Instructions. This equipment

is indoor use and all the communication wiring are limited to inside of the building.

Specifications are subject to change without notice.

Summary of Contents for 4 Channel




















































































Search results

Summary of Contents for 4 Channel

Reviews:

Costar 4 Channel, User Manual, Page: 83 / 83

Search results

Summary of Contents for 4 Channel

Reviews: