WARNING
Connect to potable water supply only.
A cold water supply is required for automatic
icemaker operation. The water pressure must be
between 40 and 120 psi (275-827 kilopascals)
INSTALLING THE WATER LINE
WHAT YOU WILL NEED
NOTE:
Only use approved plastic tubing kits if not using
copper, certain types of plastic will crack or rupture with
age and cause water damage to your home.
Cross linked High Density Polyethylene, PEX, hose is extremely
durable and is becoming increasingly preferred.
• A Copper or approved flexible type, Universal
Refrigerator Tubing Kit or Ice-Maker install kit..
• 1/4" outer diameter to connect the refrigerator to the
water supply. If using copper, be sure both ends of
the tubing are cut square.
• A cold water supply. The water pressure must be
between 20 and 120 p.s.i. (138-827 kPa).
• Power drill.
´RUDGMXVWDEOHZUHQFK
• Straight and Phillips blade screwdriver.
7ZR´RXWHU
diameter
FRPSUHVVLRQQXWVDQG
ferrules (sleeves)—to connect the copper tubing to
the shutoff valve and the refrigerator water valve.
OR
You can find kits that come with all parts included
such as Stop Tee and compression fittings.
,I\RXUH[LVWLQJFRSSHUZDWHUOLQHKDVDIODUHGILWWLQJ
at the end, you will need an adapter (available at
plumbing supply stores) to connect the water line to
the refrigerator OR you can cut off the flared fitting
with a tube cutter and then use a compression
ILWWLQJ
• Shutoff valve to connect to the cold water line.
The shutoff valve should have a water inlet with a
PLQLPXPLQVLGHGLDPHWHURI´DWWKHSRLQWRI
FRQQHFWLRQWRWKH&2/':$7(5/,1(6DGGOHW\SH
shutoff valves are included in many water supply
kits. Before purchasing, make sure a saddle-type
valve complies with your local plumbing codes.
Installation Instructions
,QVWDOOWKHVKXWRIIYDOYHRQWKHQHDUHVWIUHTXHQWO\XVHG
drinking water line.
2
CHOOSE THE VALVE LOCATION
Choose a location for the valve that is easily
DFFHVVLEOH,WLVEHVWWRFRQQHFWLQWRWKHVLGHRI
a vertical water pipe. When it is necessary to
FRQQHFWLQWRDKRUL]RQWDOZDWHUSLSHPDNHWKH
connection to the top or side, rather than at the
bottom, to avoid drawing off any sediment from
the water pipe.
1
SHUT OFF THE MAIN WATER
SUPPLY
Turn on the nearest faucet long enough to clear
the line of water.
3
DRILL THE HOLE FOR THE
VALVE
'ULOOD´KROHLQWKHZDWHUSLSHHYHQLIXVLQJ
a self-piercing valve), using a sharp bit. Remove
any burrs resulting from drilling the hole in the
pipe.
Take care not to allow water to drain into
the drill.
)DLOXUHWRGULOOD´KROHPD\UHVXOWLQUHGXFHG
ice production or smaller cubes.
INSTALLING THE WATER LINE
(cont.)
4
FASTEN THE SHUTOFF VALVE
)DVWHQWKHVKXWRIIYDOYHWRWKHFROGZDWHUSLSH
with the pipe clamp.
NOTE:
Commonwealth of Massachusetts
Plumbing Codes 248CMR shall be adhered
to. Saddle valves are illegal and use is not
permitted in Massachusetts. Consult with your
licensed plumber.
7
CONNECT TO SHUTOFF VALVE
Place the compression nut and ferrule (sleeve) for cop-
per tubing onto the end of the tubing and connect it to
the shutoff valve. Make sure the tubing is fully inserted
into the valve. Tighten the compression nut securely.
For plastic tubing with
Quick Connect (included)
tubing
kit, insert the molded end of the tubing into the shutoff
valve and tighten compression nut until it is hand tight,
then tighten one additional turn with a wrench. Over
tightening may cause leaks.
NOTE:
Commonwealth of Massachusetts
Plumbing Codes 248CMR shall be adhered
to. Saddle valves are illegal and use is not
permitted in Massachusetts. Consult with your
licensed plumber.
5
TIGHTEN THE PIPE CLAMP
Tighten the clamp screws until the sealing
washer begins to swell.
NOTE:
'RQRWRYHUWLJKWHQRU\RXPD\FUXVK
the tubing.
8
FLUSH OUT THE TUBING
Turn the main water supply on and flush out
the tubing until the water is clear.
Shut the water off at the water valve after about
one quart (1 liter), or 2 minutes, of water has
been flushed through the tubing.
6
ROUTE THE TUBING
Route the tubing between the cold water line
and the refrigerator.
Route the tubing through a hole drilled in the
wall or floor (behind the refrigerator or adjacent
base cabinet) as close to the wall as possible.
Pipe Clamp
Vertical Cold
Water Pipe
Saddle-Type
Shutoff Valve
Washer
,QOHW(QG
Pipe Clamp
Clamp
Screw
Saddle-Type
Shutoff Valve
Compression Nut
Packing Nut
Outlet Valve
)HUUXOHVOHHYH
Quick Connect
Tubing
8 9
OR
*QUICK CONNECT FITTING*
Fitting grips before it seals. Ensure
tube is pushed into the tube stop
Push the tube into the fitting all
the way up to the tube stop.
Pull on the tube to check it is secure. Turn on water
and check for leaks. (If you have leaks just cut a
small portion of hose further down to give a smooth
edge.)
To disconnect, ensure the system is depressurized
before removing the tube. Push in Quick Connect
end piece squarely against face of fitting. With it
held in this position, the tube can be removed.
Installation Instructions