background image

- 1 - 

WARNING,  Safety  & Maintenance 

 

Be  sure  that  all  users  carefully  read  and  understand  all  warning,  safety  and 

maintenance info on this Owner

s Manual or labels on the machine before each use. 

Failure to do so may result in death or serious injury. 

It is imperative that you retain this Owner

s Manual and be sure all warning labels 

are legible and intact. 

If  you  have  any  questions  about  the  operation,  set  up  or maintenance  of  this 

machine please contact the local distributors or sales agents. 

 

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. 

TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES: 

1. Inspect equipment before each workout. Check that all nuts, bolts, screws and 

pop pins are in place and fully tightened. Also, before use, check cables for signs of 

wear. Replace all worn parts immediately. Never use machine if any parts are 

damaged or missing. 

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY. 
2. Keep clear of the cables and all moving parts when the machine is in use. 

3. Always make sure all Snap Links are closed when doing any cable/pulley/strap 

exercises. 

4. Exercise with care. Perform your exercises at a smooth moderate pace; never 

perform jerky or uncoordinated movements that may cause injury. 

5. It is recommended that you should workout with a training partner. 

6. Do not allow children or minors to play on or around this equipment. 

7. If unsure of proper use of equipment, call your local distributor or agent. 

8. WARNING: Consult your physician before starting your exercise program. For 

your own safety, do not begin any exercise program without proper instruction. 

 

 

 
 
WARNING 

Safety and Maintenance of Cables

 

IMPORTANT:

 Cables are wear items. It is your responsibility to prevent unexpected breakage. 

Cable inspection should be performed daily. Inspect all cables, the nylon coating on all cables, and the area near 

the fitting at each end of each cable. 

 

Replace any damaged or worn cable immediately. 

Do not allow the machine to be used until damaged or 

worn cables are replaced. Using or allowing a machine to be used with a suspect cable can result in serious injury. 

See Owner

s Manual for more information. 

 

 

Summary of Contents for Omega ABE-10















Reviews: